Change Network Settings from the System Control
1 On the broadcast panel system control menus, select the NETWRK SETUP
menu button.
If the broadcast panel has already established connection to the switcher, you can
access the NETWRK SETUP menu from the HOME menu by pressing the SHIFT and
CUT/FILL buttons simultaneously on the ATEM 1 M/E Broadcast Panel, or the SHIFT and
DEST SHIFT buttons in the M/E 1 block of the ATEM 2 M/E Broadcast Panel. This will
reveal the NETWRK SETUP menu button so you can select the network settings.
2 The broadcast panel’s current IP address, net mask and gateway information is
displayed.
3 The next step is to decide if you want the panel to use a fixed IP address or to be
automatically assigned an IP address from a DHCP server. Select PANEL DHCP to set
this using the soft keys on the main display.
If you’re connecting direct to a switcher without a network, then you won’t have a
DHCP server to assign an IP address automatically, so you will want to select fixed.
ATEM Broadcast Panels are delivered with a fixed IP address set to 192.168.10.10, for a
direct connection.
However, if your network has lots of computers that automatically assign IP addresses
via DHCP, then you can also select DHCP on the panel so the panel can get its network
information automatically. This is possible on the panel, and it’s only the switcher itself
that always requires a fixed IP, as the switcher needs to be found by the control panels
at a known fixed address on your network.
If you select DHCP, your network settings will be complete because the panel network
settings will be obtained from the network automatically.
4 If you have elected to use a fixed IP address, you now need to set this IP address
by selecting the PANEL IP menu button and use the knobs or the numeric keypad
to edit each field as required. Changing this IP address may cause the panel to lose
communication.
5 If the subnet mask and gateway address need to be set, then select the relevant
buttons on the system control buttons to set and use knobs or the numeric
keypad to edit.
6 When any settings have been changed, SAVE and REVERT menu buttons will become
available. Select SAVE to save the changes to the new network settings, or REVERT to
ignore the changes and revert to the current network settings.
1
8 9
0 CLRCAM
2 3
4 5 6
7
ON ON ON ON
ON ON ON ON
SHIFT
SHIFT
SHIFT
SHIFT
KEY 1
CUT
KEY 2
CUT
STNG
CUT
DVE
CUT
AUX 1
AUX 7
AUX 2
AUX 8
AUX 3
AUX 9
AUX 4
AUX 10
AUX 5
AUX 11
AUX 6
AUX 12
BORD
DIP
KEY 3
CUT
KEY 4
CUT
SHIFT
DEST
KEY 1
CUT
BORD
DIP
STNG
CUT
DVE
CUT
DSK 2
CUT
SSRC
CUT
BOX 1
DSK 1
CUT
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
BOX 3BOX 2 BOX 4
SHIFT
DEST
TIE
DSK 1
TIE
DSK 2
CUT
DSK 1
CUT
DSK 2
AUTO
DSK 1
AUTO
DSK 2
WIPE STNG DVE
MIX
DIP
BKGD KEY 1 KEY 2 KEY 3 KEY 4
WIPE STNG DVE
MIX
DIP
BKGD KEY 1 KEY 2 KEY 3 KEY 4
BOX 2
BOX 4
PATT
M/E 2
KEY
M/E 2
BOX 2
BOX 4
PATT
M/E 1
KEY
M/E 1
AUTOCUT
FTB
FTB
PREV
TRANS
AUTOCUT
PREV
TRANS
TRANS
DSK
KEYS
EFFECTS
KEYS
MEDIA
PLAYER
PANEL
SETUP
COLOR
MACRO
1
RECALL
& RUN
PLAY
RECORDLOOP
PLAY
RECORD
SHOW
NAMES
RECALL
DELETE
HOME
STOP
LOOP
MACRO
1
RECALL
PLAY
RECORDLOOP
2727