Honeywell 14CE100 Series Installation Instructions Manual

Download Installation instructions manual of Honeywell 14CE100 Series Switch for Free or View it Online on All-Guides.com.

Brand: Honeywell

Category: Switch

Type: Installation instructions manual for Honeywell 14CE100 Series

Pages: 8

Download Honeywell 14CE100 Series Installation instructions manual

Honeywell 14CE100 Series Installation instructions manual - Page 1
1
Honeywell 14CE100 Series Installation instructions manual - Page 2
2
Honeywell 14CE100 Series Installation instructions manual - Page 3
3
Honeywell 14CE100 Series Installation instructions manual - Page 4
4
Honeywell 14CE100 Series Installation instructions manual - Page 5
5
Honeywell 14CE100 Series Installation instructions manual - Page 6
6
Honeywell 14CE100 Series Installation instructions manual - Page 7
7
Honeywell 14CE100 Series Installation instructions manual - Page 8
8
Installation Instructions for the 14CE100 Series Explosion-proof limit switch
Instrucciones de instalación de los interruptores de fin de carrera de la serie 14CE100
Einbauanweisungen für Explosionsgeschutzte-Positionsschalter der Serie 14CE100
Instructions d’installation pour l’interrupteur de fin de course - Anti-deflagrants série 14CE100
Istruzioni per l’installazione del finecorsa di sicurezza Serie 14CE100
Instruções de instalação do Interruptor de fim de curso da série 14CE100
Sensing and Productivity Solutions
Issue 5
50005007
1180
II 2 G Ex d IIC T6, II 2 D Ex tD A21 IP6x T85°C
mWARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
mWARNING
OPENING PRODUCTS HAZARD
DO NOT OPEN these products when energized or in a
flammable gas atmosphere.
Failure to comply with these instructions could result in
death or serious injury.
mWARNING
SPECIAL CONDITIONS
• The connecting lead (open-ended cable) of the limit switch
shall be installed as fixed wiring and sufficiently protected
against mechanical damage.
• The connecting lead (open-ended cable) of the limit switch
is only suitable for a restricted temperature range of 0 °C up
to 70 °C.
• The connecting lead (open-ended cable) of the limit
switch shall be installed in an enclosure which meets the
requirements of a recognised type of protection according
to EN60079-0, section 1, if it is connected in the explosion
hazardous area.
Failure to comply with these instructions could result in
death or serious injury.
ROUTINE MAINTENANCE
It is important to appreciate that the safe operation of your machine
will depend upon the safe efcient working of all components and
devices, which would include these switches. It is essential that a
regular maintenance routine for the machine is established and that
the routine should specically cover all components that interface
with these switches. It is imperative that any wear on the actuator
mechanism operating the switch, or on the switch itself, and also
any drift in the operating characteristics are identied at an early
stage and the necessary corrective actions implemented by the end
user, thus ensuring operator safety. The switch actuator must not be
traveled to the point where it reaches its physical end stop, or be-
yond, as damage could occur. It is good design practice not to hold
the switch actuator in the overtravel position for extended periods,
that the actuator moves freely without jamming during operation and
that the alignment of the machine actuator to the switch prevents
damage or excessive wear.
The cable gland is not designed to be removed from the enclosure.
Tampering with this connection will result in damage to the switch.
No spare parts are available.
mADVERTENCIA
LESIONES PERSONALES
NO UTILICE estos productos como dispositivos de seguridad
o de detención de emergencia, ni en otras aplicaciones
donde un fallo del producto podría causar lesiones
personales.
El no cumplir estas instrucciones puede causar la muerte
o lesiones graves.
mADVERTENCIA
PELIGRO AL ABRIR PRODUCTOS
NO ABRA estos productos cuando estén activados o cuando
se encuentren en una atmósfera que contenga polvo o gases
inflamables.
El no cumplir estas instrucciones puede causar la muerte
o lesiones graves.
mADVERTENCIA
CONDICIONES ESPECIALES
• El cable conector (de extremo abierto) del conmutador
de fin de carrera debe instalarse mediante cableado fijo y
debe estar protegido contra daño mecánico.
• El cable conector (de extremo abierto) del conmutador
de fin de carrera sólo puede utilizarse en un rango de
temperaturas de 0 °C a 70 °C.
• El cable conector (de extremo abierto) del conmutador
de fin de carrera debe instalarse en un cerramiento
que cumpla con los requisitos de un tipo de protección
reconocida según EN60079-0, sección 1, si es conectado
en una zona con peligro de explosión.
El no cumplir estas instrucciones puede causar la muerte
o lesiones graves.
MANTENIMIENTO RUTINARIO
Es importante comprender que el funcionamiento seguro de su
máquina dependerá del funcionamiento seguro y eciente de todos
sus componentes y dispositivos, entre los que se encuentran estos
interruptores. Es fundamental que se establezca una rutina regular
de mantenimiento de la máquina. Esta rutina debe cubrir de modo
especíco todos los componentes que funcionen en conjunto con
estos interruptores. Es imperativo que cualquier desgaste en el
mecanismo del actuador que hace funcionar el interruptor, o en el
interruptor mismo, así como cualquier desviación en las caracter-
ísticas de operación sea detectada en una etapa temprana y que el
usuario nal lleve a cabo las acciones correctivas apropiadas. Esto