• Home
• Brands
• Bacharach Manuals
• Bacharach MGS SERIES
• Bacharach MGS Series Installation Manual

Bacharach MGS Series Installation Manual

Download Installation manual of Bacharach MGS SERIES Controller, Remote Control for Free or View it Online on All-Guides.com.

1

2

1: OPERATING AREA AND CONDITIONS

The Bacharach MGS Series controllers provide local

alarm status indicaons (via mul-colored, per-

channel LEDs) as well as common single-level or

dual-level digital (relay) alarm outputs based on 1, 2,

4, or 6 input signals and 1 or 2 user-definable

set-points.

MGS Controllers support mulple input sensors/

transmiers (1, 2, 4, or 6 channels) based on the

model of the controller. Inputs are standard 4-20 mA

signals from MGS-series sensors or any standard,

linear, 4-20 mA transmier.

The instrument is powered 100V-230V AC (50-60Hz) or

12V DC (specified at me of order).

P/N: 6709-9002

Revision 0

January 25, 2016

2: SAFETY INSTRUCTIONS

USER MANUAL: Before using this equipment,

carefully read and strictly follow the User

Manual (part number 6709-9000). The user

must fully understand and strictly observe the

instrucons. Use the equipment only for the

purposes listed and under the condions speci-

fied in those documents.

CODE COMPLIANCE: Comply with all local and

naonal laws, rules and regulaons associated

with this equipment.

GENUINE PARTS: Use only genuine Bacharach

spare parts and accessories, otherwise proper

funconing of the equipment may be impaired.

TECHNICIAN USE ONLY: This unit must be

installed by a suitably qualified technician who

will install this unit in accordance with these

instrucons and the standards in their parcular

industry/country. Operators of the unit should

be aware of the regulaons and standards in

their industry/country for the operaon of this

unit. These notes are only intended as a guide

and the manufacturer bears no responsibility for

the installaon or operaon of this unit.

Failure to install and operate the unit in accor-

dance with these instrucons and with industry

guidelines may cause serious injury including

death and the manufacturer will not be held

responsible in this regard.

SAFE MOUNTING: This controller must be

connected by a marked, suitably located and

easily reached switch or circuit-breaker as

means of disconnecon.

WARNING: Strictly follow the instruc-

ons in the Controller Manual (part

number 6709-9000) available at

www.MyBacharach.com.

CAUTION: DO NOT MOUNT the MGS

Controller in an area that may contain

flammable liquids or vapors. Opera-

on of electrical equipment in such

an area constutes a safety hazard.

World Headquarters

621 Hunt Valley Circle

New Kensington, PA 15068 USA

Phone: 724-334-5000 • Fax: 724-334-5001

Toll Free: 1-800-736-4666

Website: www.MyBacharach.com

E-mail: [email protected]

114A Georges Street Lower

Dun Laoghaire • Co Dublin • Ireland

Phone: +353 1 284 6388 • Fax: +353 1 284 6389

INSTALLATION GUIDE

4: DIMENSIONS

ENVIRONMENTAL CONSIDERATIONS: Care-

fully consider the full range of environmental

condions to which the instruments will be

exposed.

APPLICATION CONSIDERATIONS: The specifics

of the applicaon (for example, possible leaks,

air movement/dra, etc.) must be observed.

ACCESSIBILITY CONSIDERATIONS: The degree

of accessibility required for maintenance

purposes must be granted.

ACCESSORY CONSIDERATIONS: The types of

oponal and accessory equipment that will be

used with the system must be kept in mind.

ELECTRONIC CONSIDERATIONS: The system

contains sensive electronic components that

can be easily damaged. Do not touch nor

disturb any of these components.

Mount the MGS Controller according to the

above consideraons, product dimensions (see

Secon 4), and the maximum wiring lengths

(see Secon 5).

3: MOUNTING

Controller Housing

(1-2 Channels)

0.6 in

(15.5 mm)

0.6 in (15.0 mm)

0.5 in (12.7 mm)

2.9 in (74.5 mm)

0.2 in

(4.8 mm)

0.2 in

(5.0 mm)

2.0 in

(50.0 mm)

0.4 in (10.0 mm)

Screw

Screw

0.4 in (9.0 mm)

0.5 in (12.7 mm)

0.6 in

(15.0 mm)

1-2 Sensor

Controller

Housing

O 0.18 in (4.60 mm)

O 0.20 in (5.10 mm)

Mounng

Hole

9.47 in (240.50 mm)

8.85 in (224.70 mm)

10.26 in (260.50mm)

5.13 in (130.25 mm)

9.55 in (242.50 mm)

4-6 Sensor

Controller Housing

Controller Housing

(4-6 Channels)

5: WIRING

1: Strip 0.2 to 0.25 inches (5 to 7 mm)

of wiring insulaon.

2: Connect the wires as indicated.

SHIELD WIRE WARNING: Connect the

shield of the power wires to the earth

ground of the central control system

(e.g., chassis, ground bus bar, etc.).

WARNING: The mains power supply

cable should be of an approved type

based on local regulaons. Connecon

to the mains power supply must be

made via an approved, readily-

accessible, switched and fused plug and

socket (or as per local wiring regula-

ons) which should be within 19 feet (3

meters) of the sesnor/transmier.

CABLE OPENINGS: The metal controller housing

provides a number of PG7 openings for cable glands

or plugs.

NOTE: Aer wiring is completed,

carefully re-assemble the enclosure and

its components.

Refer to the User Manual (part number 6709-

9000) at www.MyBacharach.com for detailed

instrucons on accessing the internal components

for wiring.

Refer to the Controller manual (part

number 6709-9000) at

www.MyBacharach.com for addional

wiring configuraons.