• Home
• Brands
• Crestron Manuals
• Crestron DigitalMedia DM-MD6X4
• Crestron DigitalMedia DM-MD6X4 Quick Start Manuals

Crestron DigitalMedia DM-MD6X4 Quick Start Manuals

Download Quick start manuals of Crestron DigitalMedia DM-MD6X4 Amplifier, Cell Phone for Free or View it Online on All-Guides.com.

1

2

quickstart guide

DM-MD6X4/DM-MD6X6

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

QUICKSTART DOC. 7218B (2031226) 06.17

DigitalMedia™ Distribution Center

For more information, refer to the latest version of the

DM-MD6X4/DM-MD6X6 Installation & Operation Guide, Doc. 7196.

DM-MD6X4/DM-MD6X6

1

Connections

1

To connect the Crestron

®

DM-MD6X4 or DM-MD6X6, refer to

the information below and to the illustration to the right.

(The DM-MD6X6 rear panel is shown.)

HDMI

®

Input Connections

Using HDMI cables, connect up to six HDMI digital

video/audio input devices to the HDMI input

connectors (HDMI 1 to HDMI 6).

HDMI Output Connection

Using an HDMI cable, connect an HDMI digital

video/audio output device to the HDMI output connector

(HDMI 1).

DM 8G+

®

Output Connections

Connect up to three (DM-MD6X4) or five (DM-MD6X6)

Crestron DigitalMedia 8G+

®

receivers/room controllers to

the DM 8G+ output connectors (DM 2 to DM 4 on the

DM-MD6X4 or DM 2 to DM 6 on the DM-MD6X6).

Connections can also be made to HDBaseT

®

Alliance

Certified display devices without requiring any

DM

®

receivers. (The illustration to the right shows

connections to DM-RMC-4K-100-C devices.)

For DM 8G+ or HDBaseT wiring up to 330 feet

(100 meters) between devices, use Crestron DM-CBL-8G

DigitalMedia 8G™ cable or generic CAT5e (or better)

UTP or STP.

USB HID Connection

Using a USB cable with a type B female connector,

connect a host computer or other USB HID compliant

host to the USB HID connector (USB-HID).

LAN Connection

Using an RJ-45 cable, connect the 8-pin LAN port to the

10BASE-T/100BASE-TX Ethernet network.

Power Connection

Connect one end of the included power cord to the

DM-MD6X4 or DM-MD6X6

and the other end to the ac

power source.

Configuration

2

NOTE: The DM-MD6X4 and DM-MD6X6 do not have

a power switch. Power is applied to the unit when the

supplied power cord is connected to the ac power

source.

NOTE: Shielded cable and connectors are

recommended to safeguard against unpredictable

environmental electrical noise that may impact

performance at resolutions above 1080p.

A. Access Installer Mode

1. Ensure that the home screen is

displayed. If it is not displayed, press

the HOME button. The home screen

is shown to the right.

2. Press the BACK button.

The Installer password screen

appears.

3. Enter the four-digit password. (The

default password is “1234”.) To enter

a digit, do either of the following:

Use the front panel controls to configure the DM-MD6X4 or DM-MD6X6.

Home Screen

(DM-MD6X6 Shown)

Installer Password

Screen

● If the digit ranges from 1–6, press

the appropriate INPUT or OUTPUT

button that corresponds to the digit

to be entered.

● If the digit is 0 or ranges from 7–9, use the navigation pad as follows:

Press the Up or Down navigation button as necessary until the desired

digit appears between the brackets, and then press the Select button.

Down

Left

Up

Right

Select

Navigation Pad

B. Set Input and Output Names (Optional)

For inputs 1–6, the default names are Input 1, Input 2, and so on.

For outputs 1–4 (DM-MD6X4) or outputs 1–6 (DM-MD6X6), the default names

are Output 1, Output 2, and so on.

Use the following procedure to change an input name:

1. In the Installer menu, navigate to Inputs if it

is not already highlighted, and then press the

Select button on the navigation pad.

The Input submenu appears for the currently

selected input. The name of the input

is shown at the top of the Input submenu.

(The LED of the currently selected input lights.)

2. Select the desired input by pressing the

appropriate INPUT button (1–6).

The LED of the selected input lights, and

the name of the input appears at the top of the

Input submenu.

3. Navigate to Name if it is not already highlighted, and then press the

Select button.

A scrollable list of predefined source names appears for the input.

4. Navigate to the desired source name in the list, and then press the

Select button to confirm the selection.

The selected name now appears at the top of the Input submenu for the

selected input.

After the fourth digit is correctly entered, the Installer menu appears.

Installer Menu

Input Submenu

(Input 1 Shown)

Use the following procedure to change an output name:

1. In the Installer menu, navigate to Outputs and then press the

Select button.

The Output submenu appears for the currently

selected output. The name of the output

is shown at the top of the Output submenu.

(The LED of the currently selected output lights.)

2. Select the desired output by pressing the

appropriate OUTPUT button (1–4 on the

DM-MD6X4 or 1–6 on the DM-MD6X6).

The LED of the selected output lights, and

the name of the output appears at the top of the

Output submenu.

3. Navigate to Name if it is not already highlighted, and then press the

Select button.

A scrollable list of predefined room names appears for the output.

4. Navigate to the desired room name in the list, and then press the

Select button to confirm the selection.

The selected name now appears at the top of the Output submenu for

the selected output.

Output Submenu

(Output 1 Shown)

After 30 seconds of inactivity,

the DM-MD6X4 and

DM-MD6X6 time out and return

to the home screen while

dimming the LCD.

HD cable

Blu-Ray

Disc® player

Computer

Display

HD cable

DM-RMC-4K-100-C

Display

AC power

LAN

PROCISE®

surround

system

DM-MD6X6

Ground