Samsung CY-SWC1000A User Manual
Download Operation & user’s manual of Samsung CY-SWC1000A Battery Charger for Free or View it Online on All-Guides.com.
Brand: Samsung
Category: Battery Charger
Type: Operation & user’s manual for Samsung CY-SWC1000A
Pages: 25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
English
English-1
Wireless Charger (Model: CY-SWC1000A )
User Manual
1. Product Overview
This product enables you to charge the 3D Active Glasses wirelessly. To charge the product,
you have to use this product with the 3D Active Glasses.
2. Part Names and Accessories
Accessories : Wireless charger, Adapter, AC-cord, Manual, Ferrite Core
3. How to Use
yy
Connect the power cord to the adapter at the back of the product.
yy
Connect the adapter supplied with the product to the AC power cord.
yy
When the LED at the top of the product turns red and you press the power switch slightly,
the LED turns green and the product enters charging mode. At this time, the blue LED at
the front starts blinking slowly. During charging mode, the green LED at the top turns on
and the blue LED at the front blinks so that you can easily identify the state. (This product
supports a last memory function that saves the last settings even if the power is turned off.
The LED may illuminate green according to the state when the power was last turned off.
Since the green LED indicates that the product is already in charging mode, in this case,
proceed to the next step without pressing the power button.)
yy
In charging mode, put the device that supports wireless charging on the corresponding
part of the product to start charging the device. Charging will start automatically. It is
recommended that you only use the following authorized devices that support wireless
charging.
y✎
To charge the 3D Active Glasses (SSG-3300GR, SSG-3300CR, SSG-3700CR) that support
wireless charging and that are sold separately, put the glasses on the circular wing as shown
by the figure so that the front of the glasses face outward. At this time, make sure to check the
charge status of the glasses through the LED of the 3D Active Glasses. If the LED of the 3D
Active Glasses is off, it indicates that the glasses have not been placed in position properly.
The
LED on the 3D glasses will blink while the battery is being charged. Move the glasses
until the red LED flashes. The battery is fully charged when the LED on the 3D glasses
turns green and flashes.
It is best to place the glasses within the recommended area of use
(
marked by oblique lines
) indicated in the following picture. If the glasses are outside of the
recommended area, charging may take longer.
y✎
If charging is complete or is not necessary, press the power button at the top once. The power
LED illuminates red and the product changes to standby mode. This product provides an automatic
mode switching function to save power. Approximately 5 hours after the green LED is illuminated,
the product automatically changes from charging mode to standby mode and then the LED
illuminates red.
4. Operating Precautions
y
Charging another device that is not specified in the manual is not guaranteed. Do not
place or stack incompatible devices on the product.
y
If the charging function of the product is no longer necessary or the device has been fully
charged, it is recommended that you switch to standby mode by pressing the power
button. In the standby state, the product does not emit a magnetic field and consumes
negligible power.
y
The product provides an auto-power off function to save power. Approximately 5 hours
after entering charge mode (green LED), the product automatically enters standby mode
(red LED). Please note that is not a product malfunction.
y
This product supports the last memory function that saves the last settings even if the
power is turned off. In the case of a power failure or when the AC adapter or the DC jack
is disconnected, the product remembers the last mode such as charge mode or standby
mode and automatically returns to that mode when power is supplied again. This is not a
product malfunction.
y
Since the circuitry is located at the bottom of the product, it may generate heat, but the
heat is within the safety specifications and this is not a malfunction of the product.
y
This product generates a magnetic field. Do not place the product near wireless devices
(a mobile phone, etc.), contactless cards or, communication equipment. The device may
interfere with the product and cause it to become damaged.
y
Since this product utilizes electro-magnetic resonance, the internal antennas may interfere
with each other. When using this product, avoid stacking the products or placing them
within 30 cm of each other.
y
The charging time may be affected by the age of the battery in the device to be charged
or the charge method, and the model of the product. For more information, please refer
G
A
G
I
B
;
Power switch and LED
DC adapter socket
(at the bottom back)
LED charging mode
Circular wing
Suggested range
Cylinder top
Circular wing
1.5cm (0.6 in)
Suggested range
(marked by oblique lines)
Circular wing
CY-SWC1000A_Na_L16.indb 1 2011-02-17 오후 1:19:07