Vetus XHI12W User Manual

Download Operation & user’s manual of Vetus XHI12B Security System for Free or View it Online on All-Guides.com. This version of Vetus XHI12B Manual compatible with such list of devices, as: XHI12B, XHI24B, XHI24W, XHSH, XHSM

Vetus XHI12B Operation & user’s manual - Page 1
1
Vetus XHI12B Operation & user’s manual - Page 2
2
Inleiding
Het uitlaattemperatuur-alarmsysteem geeft een visueel èn
een hoorbaar alarm als de uitlaattemperatuur, die door middel
van een zender in het uitlaatsysteem wordt gemeten, hoger is
dan 71 ˚C.
Het uitlaattemperatuur-alarmsysteem is geschikt voor 12 Volt
of voor 24 Volt en kan worden toegepast met min aan
massa of massavrij (2-polig). Let er op dat de op het waar-
schuwings-instrument aangegeven spanning overeenkomt
met de boordspanning.
De zender bevat een temperatuurbediend bimetaalcontact en
kan worden toegepast voor zowel 12 Volt als 24 Volt boordsy-
stemen.
De zender wordt geleverd in dubbelpolige uitvoering (massa-
vrij) en is voorzien van schroefdraad
1
4”- 20 UNC.
Maximale belasting 3A ohms, 2A inductief.
XHSM:
Bestemd voor montage van de sensor in Vetus uitlaatdempers
type MV en type LSG. Een verloop naar M14 x 1,5 en een borg-
moer is meegeleverd.
XHSH:
Bestemd voor montage van de sensor in een uitlaatslang. Een
slangmontageset is meegeleverd.
Installatie
N.B. De nummers verwijzen naar de tekeningnummers.
1 Waarschuwingsinstrument
Klik de afwerkring op het meetinstrument. Maak een gat in
het paneel en monteer het instrument zoals aangegeven in
de tekening.
2 De temperatuurzender in een uitlaatdemper type MV
Verwijder de borgmoer aan de binnenzijde van de ‘IN’-
aansluiting. Verwijder de plug.
Monteer het verloop, schroefdraad M14 x 1,5, en monteer de
borgmoer met een schroefdraad-borgmiddel op het verloop.
Monteer de zender.
3 De temperatuurzender in een uitlaatdemper type LSG
De ‘IN’-aansluiting van de uitlaatdemper is voorzien van twee
ronde vlakken. Deze vlakken zijn bestemd voor montage van
een temperatuurzender.
Boor in één van deze vlakken een gat van ø 14 mm. Monteer
het verloop, schroefdraad M14 x 1,5, en monteer de borgmoer
met een schroefdraad-borgmiddel op het verloop.
Zorg er voor dat na montage van het verloop de uitlaatdem-
per weer volledig vloeistof- en gasdicht is.
Monteer de zender.
4 De temperatuurzender in een uitlaatslang
De temperatuurzender dient op een afstand van minimaal
15 cm en maximaal 50 cm vanaf de plaats waar het water in
de uitlaat wordt geïnjecteerd in de uitlaatslang te worden
aangebracht.
Plaats de temperatuurzender in het bovenste deel van de
slang omdat hier de hoogste temperaturen optreden.
Boor in de uitlaatslang een gat van 8 mm.
Plaats vanaf de binnenzijde de voeler met de 0-ring in het gat
in de slang; plaats aan de buitenzijde de aandrukring op de
voeler en schroef de temperatuurzender in de voeler.
5 Aansluiten
Sluit het uitlaattemperatuur-alarmsysteem aan zoals in het
schema is aangegeven. Pas minimaal draad met een door-
snede van 1 mm
2
toe.
Introduction
The exhaust temperature alarm system is giving a visual and
audible alarm if the exhaust temperature, measured by a send-
ing unit installed in the exhaust system, is 71 degrees C (160
degrees F) or higher.
The exhaust temperature alarm system is suitable for either
12 Volt or 24 Volt and can be used with negative ground or
insulated return (2-pole system).
Make sure that the voltage indicated on the warning device
equals the ship’s power supply voltage.
The sending unit contains a temperature operated bi-metal
contact and can be used for both 12 Volt and 24 Volt system.
The sending unit is supplied in double pole version (insulated
return) and is equipped with thread
1
4”- 20 UNC.
Max. load, 3 Amp. resistive, 2 Amp. inductive.
XHSM:
Intended for installation of the sending unit into Vetus exhaust
mufflers of the models MV and LSG. An adaptor to M14 x 1.5
and a securing nut is included in the supply.
XHSH:
Intended for installation of the sensor into an exhaust hose. A
hose mounting set is included in the supply.
Installation
Note: The numbers refer to the numbers in the drawings.
1 Warning device
Click the finishing bezel on the instrument. Make a hole in
the instrument panel and fit the instrument as shown in the
drawing.
2 The temperature sender unit into a muffler model MV
Remove the securing nut at the inside of the ‘IN’ connection.
Remove the plug.
Install the adaptor; thread M14 x 1.5 and install the securing
nut onto the adaptor, use screwlock on the adaptor thread.
Install the sending unit.
3 The temperature sender unit into a muffler model LSG
At the ‘IN’ connection of the exhaust muffler are 2 circular
shaped flat surfaces. These surfaces are intended for installa-
tion of the temperature sending unit.
Drill a hole of 14 mm (
9
16”)diameter in one of these surfaces.
Install the adaptor; thread M14 x 1.5 and install the securing
nut onto the adaptor, use screwlock on the adaptor thread.
Make sure that the exhaust muffler is completely gas- and
water-tight once fitting of the adaptor is complete.
Install the sending unit.
4 The temperature sending unit into an exhaust
hose
The temperature sending must be installed in the exhaust
hose at a distance of at least 15 cm (6”) but not more than 50
cm (20”) away from the location where the water is injected
into the exhaust system.
Locate the temperature sending unit in the upper part of the
hose, the highest temperatures will occur in the upper part.
In the exhaust hose a hole must be drilIed of 8 mm (
5
16”). On
the inside, place the sensor with the O-ring into the hose. On
the outside, place the washer on the sensor and mount the
temperature sending unit into the sensor.
5 Connection
Connect the exhaust warning alarm system as indicated in the
diagram. Use wire with a cross-section of minimal 1 mm
2
(16
AWG).
65
(2
9
/
16
”)
10
(
3
/
8
”)
63
(2
1
/
2
”)
ø 53
(2
1
/
8
”)
*
1 Waarschuwingsinstrument
2 Temperatuurzender
3 Contactslot
4 Zekering
5 Accu
1 Warning device
2 Temperature sending unit
3 Key switch
4 Fuse
5 Battery
1 Warninstrument
2 Temperatursender
3 ZündschIoß
4 Sicherung
5 Batterie
1 Dispositivo de aviso
2 Unidad transmisora
de temperatura
3 Llave de contacto
4 Fusible
5 Batería
1 Strumento di allarme
2
Trasmettitore della
temperatura
3 Serratura di contatto
di accensione
4 Fusibile
5 Batteria
Exhaust temperature alarm system Exhaust temperature alarm system Exhaust temperature alarm system
Exhaust temperature alarm system
090411.01
090411.01 090411.01
1
2
4
5
3
* Benodigde inbouwdiepte
Required build-in depth
Erforderliche Einbautiefe
Profondeur d’encastrement nécessaire
Profundidad necesaria de incorporación
Profondità di montaggio necessaria
XHI12B
XHI24B
XHI12W
XHI24W
XHSM
XHSH
Uitlaatgassen
Exhaust gasses
Abgase
Gaz d’échappement
Gases de escape
Gas di scarico
Koelwater
Cooling water
Kühlwasser
Eau de refroidissement
Agua de refrigeración
Acqua di raffreddamento
NEDERLANDS
ENGLISH
vetus b.v.
FOKKERSTRAAT 571 - 3125 BD SCHIEDAM - HOLLAND
TEL.: +31 0(0)88 4884700 - sales@vetus.nl - www.vetus.com
Printed in the Netherlands
090411 2018-07