Swit S-4020 User Manual
Download Operation & user’s manual of SWIT S-4010 Power Supply for Free or View it Online on All-Guides.com.
Brand: SWIT
Category: Power Supply
Type: Operation & user’s manual
Model: SWIT S-4010 , SWIT S-4020 , SWIT S-4030
Pages: 2
1
2
S-4010/S-4020/S-4030
Power Station Box
Ver:C.2
Tel:+86-25-85805753
Fax:+86-25-85805296
http://www.swit.cc
E-mail: [email protected]
USER MANUAL
SWIT Electronics Co.,LTD.
Congratulations on your purchase of this product. Please read this user manual carefully.
Warning
Caution
Never expose this product to rain or moisture.
Never attempt to open this product, please contact the local
agent if have problems.
Never use metal or other conductors to touch the inside of
this product.
Never use the charger not provided by the manufacturer to
charge the Li-ion batteries in order to avoid damage.
Never short-circuit the output socket.
Never put this product in unstable place, it may fall and cause
serious damage.
◆
◆
◆
◆
◆
◆
Only limited to charge/discharge specied size of batteries.
Only work in the temperature between 0℃- 40℃.
Keep the terminals clean and ensure the reliable connection.
Do not cover the cooling vent.
Use the specied fuse to avoid damage.
Not support charge and discharge at the same time.
Pay attention to the selection of the output socket.
◆
◆
◆
◆
◆
◆
◆
Introduction
Feature
1. Install the V-mount battery following the arrow direction as
shown in gure 1. Battery and battery plate are well
connected with cracking sounds.
2. Use the provided battery charger to charge
(Only limited to charge/discharge specied
batteries). It may cause danger if charge
other batteries due to incompatibility
problem, see details as showed in
“Applicable Battery”. It can charge
maximum 4 V-mount batteries
simultaneously.
3. Make sure the batteries and
battery plates are well connected
before charging.
4. During charging process, pls
refer to “LED panel instruction” to
check the status.
5. When the indicator turns green,
it means fully charged.
Charging Discharging
1. Install the V-mount battery following the arrow direction as
shown in gure 1. Battery and battery plate are well connected
with cracking sounds.
2. To ensure continuous power supply and maximum power
output, it is recommended to use 4 pieces of the same
model and fully charged V-mount batteries to discharge,
otherwise the loading capacity will reduce or cause battery
and adapter protection.
3. S-4020 can output 12V or 24V according to the demands:
①. Dial up the power switch to “－”, 12V will be activate,
DC 11-16.8V has output while DC 22-33.6V has no output.
②. Dial down the power switch to ”＝”, 24V will be activate,
DC 22-33.6V has output while DC 11-16.8V has no output.
4. For S-4030, the sum of 2 channels maximum output load is 15A.
5. Please choose the proper XLR cable. Make sure this product
and load equipment are well connected and no short circuit
before loading.
6. Please change or charging the Li-ion batteries if the LED low
battery warning displays.
fig1
Applicable Battery
All SWIT V-mount batteries no larger than 168x101x68mm
Storage
Please turn o the power switch if it is not used for a long time and take out the inside V-mount batteries.
Keep in cool and dry place.
Please avoid contact with corrosive substances, away from re and heat source.
◆
◆
◆
It adopts PP+ Fiber glass case which is high intensity, high
toughness and high temperature resistant. It can install 4 pieces
of V-mount batteries which can provide more power and longer
power supply time comparing to single Li-ion battery. It can
meet the demand of dierent users, and is very suitable for Cine
cameras, lightings for Film & Television and mobile studios.
1. PP+ Fiber glass case, strong and durable
2. Install 4 x V-mount batteries
3. Charging without take out batteries by provided 4-pin XLR DC
charging socket
4. LED panel to display real-time voltage and low voltage warning
5. Intelligent protective circuit design, safe and reliable