Sharp SPC1100 Instructions & Warranty

Download Instructions & warranty of Sharp SPC1100 Clock for Free or View it Online on All-Guides.com.

Brand: Sharp

Category: Clock

Type: Instructions & warranty for Sharp SPC1100

Pages: 2

Download Sharp SPC1100 Instructions & warranty

Sharp SPC1100 Instructions & warranty - Page 1
1
Sharp SPC1100 Instructions & warranty - Page 2
2
Atomic QA Wall Clock
Instructions & Warranty
Thank you for your purchase of this quality clock. The utmost care has gone into the design and manufacture of your
clock. Please read these instructions and store them in a safe place for future reference.
The receiver unit has a clear, easy-to-read display that shows indoor temperature and humidity, outdoor temperature,
time, month, date, day. The remote sensor transmits the outdoor temperature. To receive the outdoor temperature,
place the sensor anywhere within 30 meters; the 433.92MHz technology means no wire installation is required.
The Atomic Clock will always be accurate to within one second as it receives daily WWVB updates. Daylight Saving
Time also automatically updates so there is no need to re-set the clock manually!
IMPORTANT: If the Atomic Clock does not receive the WWVB signal immediately, wait overnight and it will be
set in the morning.
The clock has a built in receiver that automatically synchronizes itself with the WWVB radio signal broadcast by the
US Governments National Institute of Standards & Technology (NIST) in Fort Collins, Colorado.
FEATURES:
Atomic QA Clock
1
The WWVB radio
signal daily broadcast ensures that the atomic clock will always display the most accurate date and time.
. QA Clock:
- Before insert the battery, select the time zone and DST mode. Once battery is inserted, the second hand will run
and stop at zero position (12:00), and then the minute and hour hands will start running and stop at zero position.
Then, the clock begins to receive the Atomic time signal automatically and it will take 3 - 10 minutes. If successfully
receive the signal, the hands will find their correct time and work normally.
NOTE:
1. The unit will automatically search for the time signal at 2:16am, 4:16am, 2:16pm, 4:16pm.
2. Closed area such as airport, basement, tower block or factory is not recommended.
3. While the atomic signal is flashing, the control panel is inactive.
2. LCD DISPLAY:
- Displays indoor/outdoor temperature; and current weather condition.
3. BATTERY COMPARTMENT AND DOOR:
- Use 2 x AA size batteries
4. / BUTTON:
- In normal mode, press the button to switch temperature unit /℉.
SPC1100
REMOTE TRANSMITTER
Recommended operating range: -50to 70℃, -122to 158
Resolution: 0.1℃/℉(above 0℃/32℉), 1℃/℉(below 0℃/32℉)
Humidity measuring range: 20% RH to 95%RH
Operating range: 20% RH to 95%RH
Resolution: 1%RH
RF transmission frequency: 433.92MHz
Remote transmitter: 1 unit
RF transmission range: maximum 30 meters
Temperature sensing cycle: around 50 seconds
POWER
Main unit: 1.5V, use 1 x AA 1.5V alkaline battery (for clock movement)
3V, use 2 x AA 1.5V alkaline battery (for LCD display)
Remote transmitter: 3V, use 2 x AA 1.5V alkaline battery
DIMENSION
Main unit: 273(W) x 360(H) x 5.3(D)mm
10.7(W) x 14.2(H) x 2.1(D)inch
Remote transmitter: 40(W) x 130(H) x 24(D)mm
1.6(W) x 5.1(H) x 0.9(D)inch
NOTE
Changes or Modifications not expressly approved by the party responsible could void the user's authority to operate
this device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
REC
WWVB
M.SET
Chan nel
Reset
C / F
REC
WWVB
M.SE T
1
2
4
5
6
3
7
9
10
11
12
13
14
8