Zte MF910 Getting Started

Download Getting started of Zte MF910 Wireless Router for Free or View it Online on All-Guides.com.

Brand: Zte

Category: Wireless Router

Type: Getting started for Zte MF910

Pages: 2

Download Zte MF910 Getting started

Zte MF910 Getting started - Page 1
1
Zte MF910 Getting started - Page 2
2
ZTE MF910
Let’s go
Getting Started With Your Device
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
LEGAL INFORMATION
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced,
translated or utilized in any form or by any means,
electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE
Corporation.
The manual is published by ZTE Corporation. We reserve
the right to make modifications on print errors or update
specications without prior notice.
Version No.: R1.0
Edition Time: June 10, 2014
Manual No.: 079584506591
NOTE:
Do not use the device in an enclosed environment or where
heat dissipation is poor. Prolonged work in such space
may cause excessive heat and raise ambient temperature,
which may lead to automatic shutdown of the device for
your safety. In the case of such event, cool the device in a
well-ventilated place before turning on for normal use.
Getting to Know Your Device
Appearance
The following gure is for your reference only.
1. SIM (or USIM) Card Cover
Reset Button
2. WPS Button
3. Power Button
4. LCD Screen
5. Charger/USB port
6. AUX Antenna Connector
7. Main Antenna Connector
NOTES:
Press and hold the Power button for about 10 to 15
seconds to restart the device.
If the battery is extremely low, you may be unable to
power on the device even when it is being charged.
In this case, try again after charging the device for
about 20 to 30 minutes. Contact customer service if
you still cannot power on the device after prolonged
charging.
Do not change the built-in rechargeable battery in
your device by yourself. The battery can only be
changed by ZTE or ZTE authorised service provider.
Indicators
When the device is powered on, the following icons may
be displayed on the LCD screen. For a description of the
icons, refer to the following table.
Icon Description
Network signal strength.
3G,4G
Network type. The 4G or 3G icon is
displayed on the LCD screen depending on
the connected network.
The user is in roaming status.
Network in use.
One or more new messages are received.
Wi-Fi status and the number of connected
users.
Battery power.
Connection Scenario
The device can access the Internet in two ways and allows
multiple clients to surf on the Internet at the same time. The
following gure is for your reference only.
4G Mode: A SIM or USIM card can be used to access
the Internet.
Internet Wi-Fi Mode: Your device can be connected to
a WLAN device (such as a hotspot device or wireless
router) through Wi-Fi to access the Internet. The WLAN
device must be already connected to the Internet.
NOTE:
Your device and the WLAN device must be in different
subnets.
Installing Your Device
1. Open the SIM (or USIM) card cover.
NOTE: Do not remove the cover rudely, because it is
connected with the device.
2. Install a SIM (or USIM) card to the SIM (or USIM) card
slot. The following gure shows the correct installation
direction. You will hear a click when the SIM (or USIM)
card is locked in place.
IMPORTANT:
Your device does not support the Micro/Nano SIM card or
any other nonstandard SIM cards. To avoid damaging the
device, do not use those cards or any card holders.
3. Close the SIM (or USIM) card cover.
Connecting Your Device
Using Wi-Fi
1. Power on your device.
2. Use the Wi-Fi application on a client to search for
available wireless networks.
NOTE:
Set the client to obtain an IP address automatically. For the
detailed procedure, refer to Conguring Your PC. The client
gets an IP address, for example, 192.168.0.101.
3. Select the SSID of your device, and then click Connect.
NOTE:
You can nd the default SSID on the label of your device.
4. Enter the password, and then click Connect.
NOTE:
You may need to enter the password for the Wi-Fi
connection. You can view the label on your device to get
the default password.
5. Wait until the client is connected to your device
successfully.
Using a USB Cable
1. Connect a client to your device through a USB cable.
2. Power on your device. The operating system detects
and identies new hardware, and automatically nishes
the installation.
NOTE:
If the system does not automatically launch installation,
you can run the installation program in the My Computer/
ZTEMODEM path.
3. Wait until the client is connected to your device
successfully.
Accessing the Internet
4G Mode
After a client is successfully connected to your device, you
can access the Internet in Automatic or Manual mode.
The default mode is Automatic.
Mode Operation
Automatic
Your device is automatically connected to
the Internet, and you can surf the Internet
through the client.
Manual
1. Log in to the webGUI conguration page,
2. Select Settings > Network Settings >
Dial-up Settings > WAN Connection
Mode > Manual, and then click Apply.
3. Select Home, and then click Connect or
Disconnect.
NOTE:
To modify the parameters of your device, log in to the
webGUI conguration page by visiting http://192.168.0.1 or
http://m.home. The default password is admin.
Internet Wi-Fi Mode
1. Log in to the webGUI conguration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network,
and then click Apply.
1 2 3 4 5 6 7 8 9 10