• Home
• Brands
• GE Manuals
• GE MDS 4710M
• GE MDS Master Station Installation Instructions Manual

GE MDS Master Station Installation Instructions Manual

Download Installation instructions manual of GE MDS 4710M Network Hardware, Network Router for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

MDS Master Station

Setup Guide

05-6398A01, Rev. C MDS Master Station Setup Guide 1

1.0 INTRODUCTION

The MDS Master Station serves as a central station in a multiple ad-

dress system (MAS) wireless network. It provides long range, duplex (or

simplex) communication between a control point and associated re-

motes. It is fully redundant for mission-critical applications, and is a

compatible replacement for older MDS x790 Master Stations.

The MDS Master Station works with a wide array of wireless equipment,

including MDS SD Transceivers, legacy MDS x710 radios, and addi-

tional wireless options, depending on the modules installed in the

chassis.

Figure 1: MDS Master Station

All modules are installed on slide-in assemblies, accessible from the

front of the unit. A protective cover on the unit’s face slides off, allowing

access to the modules and all interface connectors. In addition to

communication modules, up to two power supply units may be installed

and are available to suit a wide range of AC and DC power require-

ments.

Each module is secured to the chassis with knurled fasteners for easy

changes, when required. Figure 2 shows a common configuration of

installed modules.

Supply 1 (DC)

Supply 2 (AC)

Platform Manager

Radio A

Radio B

Alarm/Relay

Duplexer

Figure 2: Front Panel Connectors & Indicators

(Front cover removed)

Master Station modules are factory installed and cabled. Table 1:

Module Descriptions - Redundant Station describes each module

installed in a redundant configuration, from left to right. For a

non-redundant configuration, blank plates are used in place of the

redundant power supply and radio modules and a non-redundant ver-

sion of the Alarm/Relay module is installed.

The MDS Master Station supports Ethernet or serial polling depending

on order options. A host computer may be connected to the appropriate

port on the chassis (LAN for Ethernet; COM1/2 for serial signaling).

Configuration of the unit is performed through a web interface. This

requires a LAN connection to one of the Ethernet ports on the Platform

Manager module. Configuration options are similar to those of the SD

Transceiver and the radio supports full SD functionality in transparent

mode. In addition, a command line interface (CLI) is available through

the mini USB port using the proper USB drivers available at

www.gemds.com.

Table 1: Module Descriptions - Redundant Station

Module

ID

Function

Power Supply 1,

Power Supply 2

Varies

Input power supply. In a redundant

configuration, both supplies work in

tandem and are independent of which

radio is active.

Platform Manager

6834

Provides management and data interface

functions.

Radio A,

Radio B

6846

(SDM9)

Single or redundant full duplex SD Master

radios.

Alarm/Relay

6847

6848

Redundant—Active radio relay and

alarm/audio interface.

Non-redundant—Alarm and audio

interface.

Duplexer

6837

Internal RF duplexer (if equipped)

1.1 Related Documentation

In addition to this setup guide, the MDS Master Station Technical

Manual (05-6399A01, under development) provides guidance on sys-

tem design, advanced configuration, and maintenance. The Technical

Manual is available to personnel involved in the design, commissioning

and maintenance of the network. Electronic copies of the latest user

documents and support files are available free of charge at

www.gemds.com.

1.2 Options and Accessories

The MDS Master Station may be equipped with optional battery backup

(10-watt RF power output - 5 watt is standard) and a variety of duplexer

and module options. Contact your factory representative for information

on any of these options.

In addition, GE MDS offers an Accessories Selection Guide listing

additional items that may be used with many of our products. Contact

your factory representative or visit www.gemds.com for the latest copy.

1.3 Typical Application

Figure 3: Application Example on the following page shows a

common arrangement of the MDS Master Station as used in a multiple

address radio network. The system shows both SD and legacy x710

remote transceivers in use.

Depending on order options, the MDS Master Station can communicate

with remotes employing Ethernet signaling, serial signaling, or a mix of

both.