Boss Audio Systems EQ600 Introduction

Download Introduction of Boss Audio Systems EQ600 Other for Free or View it Online on All-Guides.com.

Brand: Boss Audio Systems

Category: Other

Type: Introduction for Boss Audio Systems EQ600

Pages: 4 (0.68 Mb)

Download Boss Audio Systems EQ600 Introduction

Boss Audio Systems EQ600 Introduction - Page 1
1
Boss Audio Systems EQ600 Introduction - Page 2
2
Boss Audio Systems EQ600 Introduction - Page 3
3
Boss Audio Systems EQ600 Introduction - Page 4
4
- 1 - - 2 -
Introduction
The EQ-600 is a Six Channel Pre-Amp Equalizer Network with which you can install various types of
multi-amplifier systems in a car. The EQ-600 is to be used with high quality power amplifiers and
speakers in a multi-amplifier system for hi-fi (high fidelity) sound reproduction.
You will be satisfied with the EQ-600 provides maximum flexibility to configure every possible multi-
amplifier car stereo system. Before designing and installing your system, please read this manual
thoroughly so that you can set up the system that practically suits you. Having the EQ-600 in the
center of your multi-amplifier car stereo system, your car stereo system will provide you with the
ultimate in hi-fi reproduction.
Key Features
This unit is designed for 12V DC operation only.
Avoid Installing the unit where:
- It would be subject to high temperatures, such as direct sunlight or from hot air from the heater.
- It would be exposed to rain or moisture
- It would be subject to dust or dirt
If your car is parked in direct sunlight and there is a considerable rise in temperature inside the
car, allow the unit to cool off before operating.
If this unit is placed too close to the car radio or any vehicle wires, an interference may occur, in
this case, separate the unit from the car radio and power wires.
Precautions
Location and Function of Controls (outside)
Dual-bandwidth Equalization:
Car interiors vary widely in size and acoustic make-up. The addition interior design don't make the
best location for speaker placement causing your high performance speaker system to sound not as
good as it could be. The EQ-600 provide a maximum equalization control for each area of the audio
spectrum. One-third octave bass equalization combined with one-half and full octave high frequency
equalization offers an ideal level control.
13 Volts Pre-Amp Line Driver:
The EQ-600 offers a high quality line driver that takes the low output voltage of a source unit and
increases it up to 18dB (13 volts peak). This allows you to maximize the signal-to-noise of your
system and drive your amplifiers to their maximum output without clipping. No hiss, clicks, or pops
plus maximum sound quality.
Speaker Level Inputs:
The EQ-600 has a unique high impedance speaker level input that will interface with most head units
and let you add amplifiers and speakers to your audio system.
PFM Subsonic Filter:
This unique feature is able to fine-tune the bass response of any sy stem. Why waste power on nasty
subsonic information when your Programmable Frequency Match (PFM) filter will help you clean things
up.
1. Inputs: The EQ-600 has two types of inputs, Pre-Amp and Speaker Level. These inputs should get
their signals from the main head unit and should attach to either RCA jacks or speaker leads that are
coming out of your source unit. If your source unit has a front, rear and subwoofer pre-amp output,
connect them to identical inputs on your EQ-600. If the source unit only has front and rear inputs, don't
worry about losing your bass equalization, the EQ-600 will automatically routes your subwoofer
equalization controls to the rear channels.
2. Input Gain Controls: Theses knobs allow you to increase or decrease the signal level from your
source unit to the EQ-600. Most aftermarket source units will require an increase whereas radios
installed by the automobile manufacturer will probably require you to decrease the signal level.
3. Equalization Controls: Each of these knobs control the audio spectrum. They can be adjusted
the audio output to suit your personnel taste.
4. Output Level Controls: Although your EQ-600 has the ability to increase your signal voltage to
13 volts peak, your amplifiers may not necessarily accept that much signal. These controls allow
you to regulate the proper amount of pre-amp signal from the EQ-600 to the amplifiers.
5. Output Voltage Indicators: These LED's indicate the level of signal voltage that is coming out of
the various outputs of your EQ-600.
6. Outputs: These RCA connectors should be connected to the next component after the EQ-600, such
as a crossover or amplifier. Do not connect any speakers directly to your EQ-600 or to any home
appliances.
7. Power Connections: With this connector, you can wire up the power, ground and remote turn-
on from the convenience and then casually plug it in the back of your EQ-600.
1
2 3
4
5
6
7