Glunz & Jensen PlateWriter 3000 Installation Manual

Download Installation manual of Glunz & Jensen PlateWriter 3000 Printer for Free or View it Online on All-Guides.com.

Glunz & Jensen PlateWriter 3000 Installation manual - Page 1
1
Glunz & Jensen PlateWriter 3000 Installation manual - Page 2
2
Glunz & Jensen PlateWriter 3000 Installation manual - Page 3
3
Glunz & Jensen PlateWriter 3000 Installation manual - Page 4
4
Glunz & Jensen PlateWriter 3000 Installation manual - Page 5
5
Glunz & Jensen PlateWriter 3000 Installation manual - Page 6
6
Glunz & Jensen PlateWriter 3000 Installation manual - Page 7
7
Glunz & Jensen PlateWriter 3000 Installation manual - Page 8
8
Glunz & Jensen PlateWriter 3000 Installation manual - Page 9
9
Glunz & Jensen PlateWriter 3000 Installation manual - Page 10
10
Glunz & Jensen PlateWriter 3000 Installation manual - Page 11
11
Glunz & Jensen PlateWriter 3000 Installation manual - Page 12
12
Glunz & Jensen PlateWriter 3000 Installation manual - Page 13
13
Glunz & Jensen PlateWriter 3000 Installation manual - Page 14
14
Glunz & Jensen PlateWriter 3000 Installation manual - Page 15
15
Glunz & Jensen PlateWriter 3000 Installation manual - Page 16
16
Glunz & Jensen PlateWriter 3000 Installation manual - Page 17
17
Glunz & Jensen PlateWriter 3000 Installation manual - Page 18
18
Glunz & Jensen PlateWriter 3000 Installation manual - Page 19
19
Adjustment of PlateWriter 3000
After installing the PlateWriter 3000 and after removing the print bed or replacing the
print head it is essential to check and adjust the printer on the following parameters:
Head slant (PF)/tilt and head height
Head slant (CR)/bias
Bi-directional manual adjustment on a plate
The adjustment head slant/tilt is referred to PF Head Slant in the printer service
manual. Head bias is referred to CR Head Slant in the printer service panel.
Before continuing the procedure you need to establish what plate size the system
needs to be adjusted for. Please use the table below:
Adjustment
media available
Head slant
(PF)/tilt and
head height
Head slant
(CR)/bias
Bi-directional
manual
RIP plug-in
setting
0.15 plate 0.15 plate
0.6 mm on plate
0.15 plate 0.15 plate
Narrow
8 Mill
Narrow
Plate gauge 0.2
0.2 plate 0.2 plate
0.8 mm on plate
0.2 plate 0.2 plate
Standard
8 Mill
Standard
Plate gauge 0.2
0.3 plate 0.3 plate
0.8 mm on plate
0.3 plate 0.3 plate
Standard
12 Mill
Standard
Plate gauge 0.3
0.15 and 0.3 plate 0.15 plate
0.6 mm on plate
0.15 plate 0.15 and 0.3 plate
Narrow on 0.15
and Standard on
0.3
8 Mill and 12 Mill
Narrow/Standard
Plate gauge 0.2
(Narrow) and 0.3
(Standard)
0.2 and 0.3 plate 0.2 plate
0.8 mm on plate
0.2 plate 0.2 plate
Standard
8 Mill
Standard
Plate gauge 0.2
(Standard) and 0.3
(Standard)
$
Important: Always run Narrow on 0.15 mm plates and Standard on 0.2 - 0.3
mm plates.
2-34
Installation
Adjustment of PlateWriter 3000
1126 Hardware Installation Manual - PlateWriter
TM
3000