Maytag ALD510D Service Manual

Download Service manual of Maytag ALD510 Microwave Oven for Free or View it Online on All-Guides.com. This version of Maytag ALD510 Manual compatible with such list of devices, as: ALD510, MLD510, MLD510D, P1331009M, UALD510D

Maytag ALD510 Service manual - Page 1
1
Maytag ALD510 Service manual - Page 2
2
Maytag ALD510 Service manual - Page 3
3
Maytag ALD510 Service manual - Page 4
4
Maytag ALD510 Service manual - Page 5
5
Maytag ALD510 Service manual - Page 6
6
Maytag ALD510 Service manual - Page 7
7
Maytag ALD510 Service manual - Page 8
8
Maytag ALD510 Service manual - Page 9
9
Maytag ALD510 Service manual - Page 10
10
Maytag ALD510 Service manual - Page 11
11
Maytag ALD510 Service manual - Page 12
12
Maytag ALD510 Service manual - Page 13
13
Maytag ALD510 Service manual - Page 14
14
Maytag ALD510 Service manual - Page 15
15
Maytag ALD510 Service manual - Page 16
16
Maytag ALD510 Service manual - Page 17
17
Maytag ALD510 Service manual - Page 18
18
Maytag ALD510 Service manual - Page 19
19
Maytag ALD510 Service manual - Page 20
20
Maytag ALD510 Service manual - Page 21
21
Maytag ALD510 Service manual - Page 22
22
Maytag ALD510 Service manual - Page 23
23
Maytag ALD510 Service manual - Page 24
24
Maytag ALD510 Service manual - Page 25
25
Maytag ALD510 Service manual - Page 26
26
Maytag ALD510 Service manual - Page 27
27
Maytag ALD510 Service manual - Page 28
28
Maytag ALD510 Service manual - Page 29
29
Maytag ALD510 Service manual - Page 30
30
Maytag ALD510 Service manual - Page 31
31
Maytag ALD510 Service manual - Page 32
32
Maytag ALD510 Service manual - Page 33
33
Disassembly Procedures
To avoid the risk of electrical shock, personal injury, or death,
disconnect power to oven and discharge the capacitors before
following any disassembly procedure.
WARNING
!
©2006 Maytag Services 16026969 29
Stirrer Motor
1. Disconnect power to oven.
2. Remove outer case.
3. Disconnect wire terminals from stirrer motor.
4. Remove screws securing stirrer motor to supporting
bracket.
5. Replace component and reverse procedure to
reassemble.
NOTE: When replacing stirrer motor, verify motor shaft is
aligned with antenna shaft before securing with
screws.
Magnetron Thermal Cut-Out (Mag TCO)
1. Disconnect power to unit.
2. Remove outer case, see "Outer Case" procedure.
3. Disconnect wire terminals from TCO.
4. Remove screws securing TCO to magnetron.
5. Replace component and reverse procedure to
reassemble.
NOTE: When reconnecting wiring to thermal fuses the
connectors must be tight.
Cavity Thermal Cutout (Cavity TCO)
1. Disconnect power to unit.
2. Remove outer case, see "Outer Case" procedure.
3. Disconnect wire terminals from thermal fuse.
4. Remove screw securing thermal fuse to oven cavity.
5. Replace component and reverse procedure to
reassemble.
NOTE: When reconnecting wiring to thermal fuse the
connectors must be tight.
Tray Replacement
1. Unplug oven from outlet.
2. Using a suction cup or a thin bladed screwdriver, pry
upward on front corners and remove tray from unit.
3. Thoroughly clean and degrease sump area.
4. Clean oven cavity bottom where new oven tray will
make contact using mineral spirits or any
nonflammable degreasing solvent.
NOTE: Detergents, soap, and water are not sufficient to
remove oil and grease.
5. Place new tray into unit.
Oven Light Assembly
The light bulb for inside of the oven can be changed only
by removing the outer case.
Follow these steps to change the bulb:
1. Disconnect power to unit.
2. Remove outer case, see "Outer Case" procedure.
3. Disconnect wire terminals from oven light socket.
4. Push securing tab to release oven light assembly and
lift upward to remove from interlock assembly bracket.
5. Replace component and reverse procedure to
reassemble.
NOTE: After replacing the oven light assembly, verify the
"Interlock Assembly" is properly aligned and
operating correctly.
Slow Acting Relay Assembly
1. Disconnect power to unit.
2. Remove outer case, see "Outer Case" procedure.
3. Disconnect wire terminals from relay assembly.
4. Remove slow acting relay assembly from interlock
assembly bracket.
5. Replace component and reverse procedure to
reassemble.
Air Guide
1. Disconnect power to unit.
2. Remove outer case, see "Outer Case" procedure.
3. Release plastic tabs securing top portion of light
cover to inner cavity side wall.
4. Lift upward on light cover to release bottom securing
tabs.
5. Replace component and reverse procedure to
reassemble.