Omnitronic C-50A User Manual

Download Operation & user’s manual of Omnitronic C-50A Speaker System for Free or View it Online on All-Guides.com.

Omnitronic C-50A Operation & user’s manual - Page 1
1
Omnitronic C-50A Operation & user’s manual - Page 2
2
Omnitronic C-50A Operation & user’s manual - Page 3
3
Omnitronic C-50A Operation & user’s manual - Page 4
4
Omnitronic C-50A Operation & user’s manual - Page 5
5
Omnitronic C-50A Operation & user’s manual - Page 6
6
Omnitronic C-50A Operation & user’s manual - Page 7
7
Omnitronic C-50A Operation & user’s manual - Page 8
8
Omnitronic C-50A Operation & user’s manual - Page 9
9
Omnitronic C-50A Operation & user’s manual - Page 10
10
Omnitronic C-50A Operation & user’s manual - Page 11
11
Omnitronic C-50A Operation & user’s manual - Page 12
12
Omnitronic C-50A Operation & user’s manual - Page 13
13
Omnitronic C-50A Operation & user’s manual - Page 14
14
Omnitronic C-50A Operation & user’s manual - Page 15
15
Omnitronic C-50A Operation & user’s manual - Page 16
16
Omnitronic C-50A Operation & user’s manual - Page 17
17
Omnitronic C-50A Operation & user’s manual - Page 18
18
Omnitronic C-50A Operation & user’s manual - Page 19
19
Omnitronic C-50A Operation & user’s manual - Page 20
20
Omnitronic C-50A Operation & user’s manual - Page 21
21
Omnitronic C-50A Operation & user’s manual - Page 22
22
Omnitronic C-50A Operation & user’s manual - Page 23
23
Omnitronic C-50A Operation & user’s manual - Page 24
24
Omnitronic C-50A Operation & user’s manual - Page 25
25
Omnitronic C-50A Operation & user’s manual - Page 26
26
Omnitronic C-50A Operation & user’s manual - Page 27
27
C_SERIES_ACTIVE.DOC
25/26
OPERATION
Connection with the mains
Connect the device to the mains with the power-plug.
The occupation of the connection-cables is as follows:
Cable Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IEC-
standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Switch the device on. After switching on the speaker-system, wait 8 to 10 seconds until you turn the volume-
control in order to avoid speaker-damage.
Caution! Increase the level of each channel only so far that the CLIP-LED lights up shortly. Thus, you avoid
that the output signal is distorted and your speakers are damaged.
When operating the speaker-system, please make sure that the loudspeakers always sound well. When
distorsions can be heard, either the amplifier or the loudspeaker is overloaded. Overloads can quickly lead to
amplifier or speaker damage.
In order to avoid damage, please reduce the volume immediately when distortions can be heard. When
speaker-systems are destroyed by overload, the guarantee becomes void.
Always check the sound pressure level with a meter in order to keep to the threshold.
If you want to switch off the system, switch off the speaker-system first in order to avoid acoustic shocks
on the speakers.