NAPCO RPXP6GT Installation Instructions Manual
Download Installation instructions manual of NAPCO RPXP6GT Keypad, Security System for Free or View it Online on All-Guides.com.
Brand: NAPCO
Category: Keypad , Security System
Type: Installation instructions manual
Model: NAPCO RPXP6GT , NAPCO XP-600
Pages: 28
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
11
A
8
+ User 1 Code - User Program
Mode
A
9
Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds will be silenced except for
keypad feedback beeps and Keypad Sounder
on Alarm.
User Commands - Optional
A 0
Easy Exit/Easy Arm
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones. Enter
a0
to arm the panel. To disarm the panel a valid
Arm/Disarm code must be entered. Requires
Easy Exit/Easy Arm [21-2] to be enabled.
A
3
Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
15) for 5 seconds.
Dealer Commands
A6
Download (Programming
Required)
Establish a connection between the PCD phone
line and the Control Panel phone line. When
ready, tell the installer to arm, then disarm. Then
enter
A
6
in order to establish a connection.
Phone connection to installer will go "dead" as
downloader and panel connect.
A
7
Fault Find ON/OFF
Hardwired Zone Operation
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored.
Wireless Operation
(Signal Strength)
While in Fault Find mode the keypad will provide
an audible (Table 6) and visual (Figure 5)
indication of each transmitter’s signal strength.
The signal strength metering is based on a scale
of 4 to 10, with 4 being marginal and 10 being
excellent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the
transmitter. See Table 6. Each beep is 1-
second long. The keypad will sound a short
beep for transmitters with signal strengths of 3
or less.
Signal Strength Logging Mode
The Signal Strength Logging Mode is a
troubleshooting tool which allows the collection
of signal strength information for all transmitters
on the system. Normally the Signal Strength of
Supervisory Signals are not logged; during
Signal Strength Logging Mode the signal
strength information for all supervisory signals
received over a two hour period will be saved to
the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour
test period where all supervisory signals will log
signal strength information.
TABLE
6
A
UDIBLE
S
IGNAL
S
TRENGTH
I
NDICATION
FIGURE
5
V
ISUAL
S
IGNAL
S
TRENGTH
I
NDICATION
5 6-7 4 8-10
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 1
ZONE 2
ZONE 3
ZONE 4
SIGNAL
STRENGTH
KEYPAD
SOUNDER
3 or less .25
S
BEEP
4
BEEP
5
BEEP
BEEP
6-7
BEEP
BEEP
BEEP
8-10
BEEP
BEEP
BEEP
BEEP