• Home
• Brands
• MULTIQUIP Manuals
• MULTIQUIP Mikasa MVH-402DSB
• Multiquip Mikasa MVH-402DSB Operation And Parts Manual

Multiquip Mikasa MVH-402DSB Operation And Parts Manual

Download Operation and parts manual of MULTIQUIP Mikasa MVH-402DSB Garbage Disposal for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 21

MVH-402DSB — MAINTENANCE

Engine Oil Replacement:

1. Replace engine oil, first in 25 hours of operation and every

50 to 100 hours afterwards.

2. Oil may be drained more easily when it is warm after

operation (For more details, see separate engine Owner's

Manual).

Air Filter

1. The air filter element should be cleaned because a clogged

air cleaner can cause poor engine starting, lack of power

and shorten engine life substantially.

2. To clean or replace air filter loosen the wing nut on the air

filter housing (Figure 18), remove the cover and take out air

filter cartridge. If only cleaning of the air filter is desired blow

through the air filter cartridge from the inside, moving a jet of

dry compressed air up and down until all dust is removed.

z

Reinstalling the V-belt

Engage V-belt to lower vibrator pulley and push the V-belt to left

side of upper clutch and, in the same manner as in removal,

rotate offset wrench clockwise so that the V-belt goes back on.

z

Replacing the V-belt

Remove the belt cover. Engage an offset wrench (19 mm) or the

like to vibrator pulley (lower) fastening bolt. Engage waste cloth

or the like at midway of V-belt on the left side and while pulling it

back strongly, rotate the offset wrench clockwise so that the V-

belt will come off.

z

Checking Clutch

Check the clutch simultaneously with V-belt checking. With belt

cover removed, check outer drum of the clutch for seizure and

"V" groove for wear or damage with your eyes. Clean the "V"

groove as necessary. Wear of lining or shoe should be checked

with running check. If the shoe is worn, power transmission

becomes deficient and slipping will result.

z

Replacing Clutch

Remove V-belt. Remove bolt at engine power output by giving a

shock to an engaged wrench (tapping with hammer or the like)

and rotating bolt counterclockwise. Remove clutch with a pulley

extractor. To reinstall, reverse the procedure.

CAUTION

Whenever the compactor's vibration becomes weak

or lost during normal operation regardless of opera-

tion hours, check the V-belt and clutch immediately.

Figure 19. V-Belt Hazard

CLUTCH

PULLEY

VIBRATOR

PULLEY

Figure 18. Engine Air Filter and Element

Figure 20. V-Belt Check

CAUTION

NEVER attempt to check the V-belt with the engine

running. Severe injury can occur if your hand gets

caught between the V-belt and the clutch (Figure 19).

Always use safety gloves.

Checking and Replacing the V-Belt and Clutch

1. After 200 hours of operation, remove the belt cover to check

the V-belt tension (Figure 20). Tension is proper if the belt

bends about 10 mm when depressed strongly with finger

between shafts. Loose or worn V-belts reduces power

transmission efficiency, causing weak compaction and

reduces the life of the belt itself.