Motorola SG2-DRT-3X Installation Sheet

Download Installation sheet of Motorola SG2-DRT-3X Transmitter for Free or View it Online on All-Guides.com.

Brand: Motorola

Category: Transmitter

Type: Installation sheet for Motorola SG2-DRT-3X

Pages: 16

Download Motorola SG2-DRT-3X Installation sheet

Motorola SG2-DRT-3X Installation sheet - Page 1
1
Motorola SG2-DRT-3X Installation sheet - Page 2
2
Motorola SG2-DRT-3X Installation sheet - Page 3
3
Motorola SG2-DRT-3X Installation sheet - Page 4
4
Motorola SG2-DRT-3X Installation sheet - Page 5
5
Motorola SG2-DRT-3X Installation sheet - Page 6
6
Motorola SG2-DRT-3X Installation sheet - Page 7
7
Motorola SG2-DRT-3X Installation sheet - Page 8
8
Motorola SG2-DRT-3X Installation sheet - Page 9
9
Motorola SG2-DRT-3X Installation sheet - Page 10
10
Motorola SG2-DRT-3X Installation sheet - Page 11
11
Motorola SG2-DRT-3X Installation sheet - Page 12
12
Motorola SG2-DRT-3X Installation sheet - Page 13
13
Motorola SG2-DRT-3X Installation sheet - Page 14
14
Motorola SG2-DRT-3X Installation sheet - Page 15
15
Motorola SG2-DRT-3X Installation sheet - Page 16
16
SG2-DRT-3X Installation Sheet
STARLINE
®
SG2-DRT-3X
Installation Sheet 494828-001
This Installation Sheet describes the procedure for installing the SG2-DRT-3X in the SG2440 or
SG2000 node.
The Motorola
®
Digital Return Transmitter (SG2-DRT-3X) converts three independent 5 to
42 MHz analog RF return-path signals into one digital optical signal within the SG2000 and
SG2440 nodes. This digital optical signal, with 10-bit resolution and 3.1 Gbps rate, is suitable
for optical transmission to the GX2-DRR-3X Digital Return Receiver (DRR) where the original
analog return-path signals are recreated.
The transmitter is factory-configured with either a dense wave division multiplexing (DWDM)
laser on the International Telecommunications Union (ITU) grid or a coarse wave division
multiplexing (CWDM) laser that is applicable to the required link. Motorola provides standard
models that are identified in the subsection SG2-DRT-3X Models at the end of this document.
The specific wavelengths are stamped on the label of each transmitter.
An Automatic Power Control (APC) system regulates the optical output power from the laser.
The unit provides automatic gain control (AGC) and requires no adjustment. The SG2-DRT-3X
features alarm LEDs to report local status information.
To facilitate easy upgrades, the SG2-DRT-3X has the same set-up levels as the analog return
transmitters. The double-wide module occupies the same locations as the two analog
transmitters in the node lid. The SG2-DRT-3X generates its own 5 V power and works with a
single SG2-PS2 or SG2-PS power supply.
Related Documentation
In addition to this Installation Sheet, the SG2440 Telecommunications Optical Node
Installation and Operation Manual and the SG2000 Telecommunications Optical Node
Installation and Operation Manual are required to install the SG2-DRT-3X. If you do not have
these documents, you can obtain them at the Motorola Web site.
Document Conventions
Before you begin using this Installation Sheet, familiarize yourself with the stylistic conventions
used in this document:
SMALL CAPS Denotes silk-screening on the equipment, typically representing input/output (I/O) and power
supply connections
*
(asterisk)
Indicates that several versions of the same model number exist and the information applies to all
models; when the information applies to a specific model, the complete model number is given
Before You Begin
Before you install the SG2-DRT-3X, verify that you have received the SG2-DRT-3X-CH*Kit,
part number 498284-TAB.