Maytag MMV5156AAS Installation Instructions Manual

Download Installation instructions manual of Maytag MMV5156AAB Microwave Oven for Free or View it Online on All-Guides.com. This version of Maytag MMV5156AAB Manual compatible with such list of devices, as: MMV5156AAB, MMV5156AAQ, MMV5156AAS, MMV5156AAW

Maytag MMV5156AAB Installation instructions manual - Page 1
1
Maytag MMV5156AAB Installation instructions manual - Page 2
2
Maytag MMV5156AAB Installation instructions manual - Page 3
3
Maytag MMV5156AAB Installation instructions manual - Page 4
4
Maytag MMV5156AAB Installation instructions manual - Page 5
5
Maytag MMV5156AAB Installation instructions manual - Page 6
6
Maytag MMV5156AAB Installation instructions manual - Page 7
7
Maytag MMV5156AAB Installation instructions manual - Page 8
8
Maytag MMV5156AAB Installation instructions manual - Page 9
9
Maytag MMV5156AAB Installation instructions manual - Page 10
10
Maytag MMV5156AAB Installation instructions manual - Page 11
11
Maytag MMV5156AAB Installation instructions manual - Page 12
12
Maytag MMV5156AAB Installation instructions manual - Page 13
13
Maytag MMV5156AAB Installation instructions manual - Page 14
14
Maytag MMV5156AAB Installation instructions manual - Page 15
15
Maytag MMV5156AAB Installation instructions manual - Page 16
16
Maytag MMV5156AAB Installation instructions manual - Page 17
17
Maytag MMV5156AAB Installation instructions manual - Page 18
18
Maytag MMV5156AAB Installation instructions manual - Page 19
19
STEP 3: Prepare The Venting Blower
WARNING
To avoid risk of property damage, unplug the microwave oven or disconnect power at
source by removing fuse or throwing circuit breaker.
To avoid risk of personal injury, wear protective gloves when handling mounting plate.
DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical
shock.
Your microwave oven is shipped with the blower assembled for roof venting. If you want wall-venting or
room-vented (recirculating) installation, you must change the fan, as detailed below.
Before You Start
1. Remove any shipping materials and parts from inside the
microwave oven.
2. Cover the counter top or cooktop with a thick, protective
covering to protect it from damage and dirt. See Figure 10.
NOTE: If you have a free-standing range, disconnect it, move it
onto a piece of cardboard or hardboard and pull it away
from the wall, so that you can get closer to the upper
cabinet and back wall for easier measuring and drilling.
Remove The Mounting Plate:
1. Remove mounting plate screw(s) (1 or 2 screws) from the
mounting plate as shown and discard. See Figure 11.
2. This plate will be used as the rear mounting plate. (It will be
used to locate and mark the mounting holes on the rear wall.)
3. Locate exhaust adaptor, grease filters and hardware packet.
4. At this point, remove any adhesive tape (if there is any), on the
exhaust adaptor, the grease filters and the power supply cord.
Roof-Vented Installation:
This oven is shipped assembled for roof-vented. You will need to
install the exhaust adaptor regardless of cabinet.
1. Attach the exhaust adaptor to the blower plate by sliding it into
the guides. See Figure 12.
Wall-Vented Installation:
1. Remove one blower unit mounting screw and one or two
blower plate screw(s). Remove the blower plate from cabinet.
See Figure 13.
2. Carefully lift the blower unit out of the microwave oven.
3. Use side cutters or thin snips to cut and remove knockouts "B"
from Back plate. Discard knockouts. Be careful not to distort
the plate. See Figure 14.
A thick, protective
covering
Figure 10
i
_ Mounting plate
L! Mountingplate
iI
_ n !_-_ screw(s)
(1 or 2 screws)
-- Controi Panel Side
Figure 11
..,,,_.._ Exh au st
adaptor
_/__Baok
o,oven
f---Blower Plate
unting Screw
lower Plate
__- Back Plate
Blower Unit _ II
- [j_.._,_-. -/'_ Blowe r Plate
" Mounting Screw
Parts "B"
Figure 13
uts Parts 'B"
Figure 14
11