Maytag W10267633A Installation Instructions Manual

Download Installation instructions manual of Maytag Cabrio,- WED7300X Dryer for Free or View it Online on All-Guides.com. This version of Maytag Cabrio,- WED7300X Manual compatible with such list of devices, as: Cabrio,- WED7300X, Cabrio,- WED7400X, Cabrio,- WED7800X, WED6400SB - Cabrio 7.0 Cu Ft Capacity Electric Dryer, WED6600

Maytag Cabrio,- WED7300X Installation instructions manual - Page 1
1
Maytag Cabrio,- WED7300X Installation instructions manual - Page 2
2
Maytag Cabrio,- WED7300X Installation instructions manual - Page 3
3
Maytag Cabrio,- WED7300X Installation instructions manual - Page 4
4
Maytag Cabrio,- WED7300X Installation instructions manual - Page 5
5
Maytag Cabrio,- WED7300X Installation instructions manual - Page 6
6
Maytag Cabrio,- WED7300X Installation instructions manual - Page 7
7
Maytag Cabrio,- WED7300X Installation instructions manual - Page 8
8
Maytag Cabrio,- WED7300X Installation instructions manual - Page 9
9
Maytag Cabrio,- WED7300X Installation instructions manual - Page 10
10
Maytag Cabrio,- WED7300X Installation instructions manual - Page 11
11
Maytag Cabrio,- WED7300X Installation instructions manual - Page 12
12
Maytag Cabrio,- WED7300X Installation instructions manual - Page 13
13
Maytag Cabrio,- WED7300X Installation instructions manual - Page 14
14
Maytag Cabrio,- WED7300X Installation instructions manual - Page 15
15
Maytag Cabrio,- WED7300X Installation instructions manual - Page 16
16
13
4. Using pliers, tighten the couplings with an additional two-thirds
turn.
NOTE: Do not overtighten. Damage to the coupling can result.
5. Attach
“Y” connector to brass male end of small hose. Screw on
coupling by hand until it is seated on connector.
6. A
ttach straight end of long hose to “Y” connector.
7. Attach
washer cold inlet hose to other end of “Y” connector.
Screw on coupling by hand until it is seated on connector.
8. U
sing pliers, tighten the couplings an additional two-thirds turn.
A
A. Inlet to cold water
NOTE: Do not overtighten. Damage to the coupling can result.
9. Attach
angled end of long hose to fill valve at bottom of dryer
back panel. Screw on coupling by hand until it is seated on fill
valve connector.
10. U
sing pliers, tighten the coupling an additional two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
11. Check that the water faucets ar
e on.
12. Check for leaks ar
ound “Y” connector, faucet, and hoses.
LEVEL DRYER
Check the levelness of the dryer by first placing a level on the top
of the dryer near the console.
Then, by placing a level in the crease on the side of the dryer
be
tween the top of the dryer and the dryer cabinet, check
the levelness from front to back.
If the dryer is not level, prop up the dryer using a wood block. Use a
wrench to adjust the legs up or down and check again for levelness.
COMPLETE INSTALLATION
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Ch
eck that you have all of your tools.
3. Dispose of/r
ecycle all packaging materials.
4. Check the dryer’s final location. Be sure the vent is not crushed
or kinked.
5. Ch
eck that the dryer is level. See “Level Dryer.”
6. Remove the blue film
on the console and any tape remaining on
the dryer.
7. Wipe the dr
yer drum interior thoroughly with a damp cloth to
remove any dust.
8. Read “Dryer Use” in your Use and
Care Guide.
9. For power supply cord installation, plug into a grounded outlet.
For direct wire installation, turn on power.
Steam Models Only:
10. Be su
re the water faucets are on.
11. Check for leaks around “Y” connector, faucet, and hoses.
12. If you live in a har
d water area, use of a water softener is
recommended to control the buildup of scale through the water
system in the dryer. Over time, the buildup of lime scale may clog
different parts of the water system, which will reduce product
performance. Excessive scale buildup may lead to the need for
certain part replacement or repair.