Maytag W10096988A Installation Instructions Manual

Download Installation instructions manual of Maytag Cabrio,- WED5500X Dryer for Free or View it Online on All-Guides.com. This version of Maytag Cabrio,- WED5500X Manual compatible with such list of devices, as: Cabrio,- WED5700X, MEDX600XW, WED5500XW, WED5600XW, WED5700XL

Maytag Cabrio,- WED5500X Installation instructions manual - Page 1
1
Maytag Cabrio,- WED5500X Installation instructions manual - Page 2
2
Maytag Cabrio,- WED5500X Installation instructions manual - Page 3
3
Maytag Cabrio,- WED5500X Installation instructions manual - Page 4
4
Maytag Cabrio,- WED5500X Installation instructions manual - Page 5
5
Maytag Cabrio,- WED5500X Installation instructions manual - Page 6
6
Maytag Cabrio,- WED5500X Installation instructions manual - Page 7
7
Maytag Cabrio,- WED5500X Installation instructions manual - Page 8
8
Maytag Cabrio,- WED5500X Installation instructions manual - Page 9
9
Maytag Cabrio,- WED5500X Installation instructions manual - Page 10
10
Maytag Cabrio,- WED5500X Installation instructions manual - Page 11
11
Maytag Cabrio,- WED5500X Installation instructions manual - Page 12
12
Maytag Cabrio,- WED5500X Installation instructions manual - Page 13
13
Maytag Cabrio,- WED5500X Installation instructions manual - Page 14
14
Maytag Cabrio,- WED5500X Installation instructions manual - Page 15
15
Maytag Cabrio,- WED5500X Installation instructions manual - Page 16
16
Maytag Cabrio,- WED5500X Installation instructions manual - Page 17
17
Maytag Cabrio,- WED5500X Installation instructions manual - Page 18
18
Maytag Cabrio,- WED5500X Installation instructions manual - Page 19
19
Maytag Cabrio,- WED5500X Installation instructions manual - Page 20
20
10
4-wire Direct Wire Connection
IMPORTANT: A 4-wire connection is required for mobile
homes and where local codes do not permit 3-wire
connections.
5. Prepare to connect neutral
ground wire and neutral wire
E
A
B
Remove center, silver-colored terminal block screw (B).
Remove neutral ground wire (E) from external ground
conductor screw (A).
Unscrew the removable conduit connector (A) and any
screws from a 3/4" (19 mm) UL listed strain relief (UL marking
on strain relief). Put the threaded section of the strain relief
(C) through the hole below the terminal block opening (B).
Reaching inside the terminal block opening, screw the
removable conduit connector (A) onto the strain relief threads.
A
B
C
1. Attach direct wire strain relief
Put direct wire cable through the strain relief. The strain
relief should have a tight t with the dryer cabinet and be in
a horizontal position. Tighten strain relief screw against the
direct wire cable.
For 3-wire Direct Wire Connection, see page 11.
For 4 wire Direct Wire Connection, continue to step 3 on
this page.
2. Attach direct wire cable
to strain relief
Direct wire strain relief
Direct wire cable must have 5 ft. (1.52 m) of extra length so
dryer may be moved if needed.
Strip 5" (127 mm) of outer covering from end of cable,
leaving bare ground wire at 5" (127 mm). Cut 1
1
/
2
" (38 mm)
from remaining 3 wires. Strip insulation back 1" (25 mm).
Shape ends of wires into hooks.
1"
(25 mm)
5"
(127 mm)
3. Prepare your 4-wire cable for
direct connection
To connect wires to terminal block, place hooked end of
wire under terminal block screw, facing to the right, squeeze
hooked end together and tighten screw.
4. Connect wires to terminal block
Direct Wire Connection