Avocent SwitchView SC4 DVI Quick Installation Manual

Download Quick installation manual of Avocent SwitchView SC4 DVI Switch for Free or View it Online on All-Guides.com.

Brand: Avocent

Category: Switch

Type: Quick installation manual for Avocent SwitchView SC4 DVI

Pages: 4 (1.03 Mb)

Download Avocent SwitchView SC4 DVI Quick installation manual

Avocent SwitchView SC4 DVI Quick installation manual - Page 1
1
Avocent SwitchView SC4 DVI Quick installation manual - Page 2
2
Avocent SwitchView SC4 DVI Quick installation manual - Page 3
3
Avocent SwitchView SC4 DVI Quick installation manual - Page 4
4
Powering your system
Locate the power cord that came with your switch.
Plug one end into the IEC power connector on the
SwitchView switch. Ensure the power switch is off,
then plug the other end of the power cord into an AC
wall outlet. Power up your switch fi rst, then power up
all attached servers.
Switching your servers
Press the appropriate front panel button labeled A-D to
access servers in your SwitchView switching system.
Mechanical
H x W x D = 1.75” x 11” x 11” (4.44 x 27.94 x 27.94 cm)
Weight = 4.91 lbs (2.2 kg)
The Power of Being There
®
Quick Installation Guide
SwitchView
®
SC4 DVI Switch
The following instructions will help you install
your SwitchView SC4 DVI switch.
Should you require further assistance, please
contact Avocent Technical Support.
To install the SwitchView SC4 DVI switch
To Contact Avocent Technical Support CALL (888) 793-8763 VISIT www.avocent.com/support DOWNLOAD www.avocent.com
Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its affi liates. ©2006 Avocent Corporation. All rights reserved. 590-616-616A
Connecting local peripherals
Power down all servers that will be part of your
SwitchView SC4 DVI switching system. Locate
your PS/2 keyboard, DVI monitor and PS/2
mouse. Plug your DVI monitor cable into the
appropriate CONSOLE port on the left side of
the back of your switch. Plug your PS/2 keyboard
and your PS/2 mouse cables into the keyboard
and mouse ports respectively.
Connecting your servers
Locate your rst cable set consisting of two PS/2
cables and one DVI cable. The SwitchView SC4
DVI switching system has four port sets labeled
A-D on the rear of the unit. Plug the two PS/2 cables
(keyboard and mouse) and the DVI cable (monitor)
into the corresponding ports on your server.
Plug the other ends into any available server port
set on your SwitchView SC4 DVI switching
system. Repeat this process until all servers are
attached to the SwitchView SC4 DVI switch.
Power down all
connected servers.
Connect your
peripherals to the
CONSOLE ports
on the switch.
Connect the four servers
to the switch with the
provided cables.
Press the
appropriate front
panel button
labeled A-D to
access servers in
your system.
Environmental
Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)
Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)
Input Power: 60 W; Operating Voltage 100-240 VAC
Power Frequency: 50-60 Hz
Supported Hardware
Server: IBM, PC/AT, PS/2 and 100% compatibles
Video Modes: VGA, SVGA, XGA, SXGA,
UXGA, WVGA, WSVGA, WXGA, WSXGA,
WUGA and HDTV
Maximum Resolution: 1920 x 1080 @ 60Hz
Peripherals: PS/2 keyboard, PS/2 mouse and
IntelliMouse (PS/2 only)
Power up
your system.
Optional
RF ground
(not required
for safety)
Notifi cation pour les États-Unis
Avertissement : Les modi cations apportées à ce produit sans l’accord exprès de la partie responsable de la
conformité peuvent annuler l’autorisation dont vous bénéfi ciez pour utiliser cet équipement.
Nota : L’équipement a été testé et déclaré conforme aux limites dé nies pour les appareils nuriques de classe
A, suivant l’article 15 du règlement de la FCC. Ces limites garantissent une protection suf sante contre les effets
dangereux liés à l’utilisation de l’équipement dans un environnement professionnel. L’appareil gére, utilise et peut
émettre des ondes de radiofréquence et, s’il n’est pas installé et utilisé conforment au manuel d’instructions, peut
provoquer de dangereuses interrences avec les communications radio. Lors de l’utilisation de l’appareil dans une
zone d’habitation, il est probable que des interférences dangereuses soient provoquées, auquel cas vous devez y
redier à vos propres frais.
Notifi cation canadienne
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Notifi cation japonaise
Certifi cations et labels
de sécurité et EMC
UL, FCC, cUL, ICES-003, CE, VCCI, C-Tick
Les certi cations de sécurité et EMC de ce produit portent difrents noms : CMN (Certifi cation Model Number ou
Nuro de mole de conformité), MPN (Manufacturer’s Part Number ou Numéro de référence du fabricant) ou
Sales Level Model (Mole de niveau de vente). Le nom faisant référence aux rapports et certi cats EMC et/ou de
sécurité est imprimé sur létiquette du produit.
Mesures de sécurité
DANGER, HAUTE TENSION
Ce symbole est destiné à vous avertir de la présence de « tensions dangereuses » non isoes à l’intérieur de
l’appareil pouvant être suf samment élevées pour constituer un risque de choc électrique pour les individus.
NOTA : La meilleure façon de mettre l’équipement hors tension est de le débrancher de la prise de courant.
INSTRUCTIONS
Ce symbole est destiné à attirer votre attention sur la psence de consignes importantes liées au fonctionnement et
à la maintenance (l’entretien).
AVERTISSEMENT : Pour éviter d’endommager votre matériel et écarter tout risque d’électrocution, respectez les
précautions suivantes :
- Ne retirez pas la prise de terre. Cette prise est un ément de sécurité essentiel.
- Branchez le cordon d’alimentation dans une prise reliée à la terre et facilement accessible à tout moment.
- Coupez l’alimentation du matériel en débranchant le cordon d’alimentation au niveau de la prise ou directement sur le
matériel.
590-616-616A.indd 1-2590-616-616A.indd 1-2 4/6/06 3:29:41 PM4/6/06 3:29:41 PM