• Home
• Brands
• Honeywell Manuals
• Honeywell Ademco 5883
• Honeywell Ademco 5883 Installation And Setup Manual

Honeywell Ademco 5883 Installation And Setup Manual

Download Installation and setup manual of Honeywell Ademco 5883 Transceiver for Free or View it Online on All-Guides.com.

1

2

3

4

K3791 3/04 Rev. B

$'(0&2

7UDQVFHLYHU0RGXOH



INSTALLATION AND SETUP GUIDE

INTRODUCTION

The 5883 RF Transceiver Module:

contains an RF receiver and a transmitter,

is intended for use with 5800 series RF transmitters, including bi-

directional wireless units (e.g. 5804BD), and the 5800RL Wireless

Relay Module (see Fig. 1),

receives alarm, status, and control messages from 5800

transmitters, and passes these messages to the control panel via

wired connections, which then responds accordingly (arm/disarm the

system, initiate an alarm, etc.),

transmits system status and other conditions to bi-directional

devices (e.g., 5804BD),

emulates the functions of a 5800TM module, and can control the

relays on the 5800RL Wireless Relay Module,

features a Spatial Diversity system that virtually eliminates the

possibility of "Nulls" and "Dead Spots" within the coverage area,

incorporates new high-security encryption technology (UL-864 and

RF Jam Detect),

supports the number of zones shown in the chart at right.

RF Zones Supported

5883M Up to 16 zones

5883H Depends on the control with which it is used. See the

control panel’s instructions for specific details.

If "SET UP ERROR" (alpha keypads) or "E4 or “E8”" (fixed-word

keypads) is displayed on the system's keypad, it indicates that

more than the permitted number of wireless zones have been

programmed, and none of the zones will be protected.

KEYPAD

TERMINALS

ON CONTROL

BOARD

CONTROL

PANEL*

DATA O UT

TO 5883

DATA IN TO

CONTROL

*CONTROL MUST BE CAPABLE OF

SUPPORTING A 5800 RF SYSTEM

5883

TRANSCEIVER

5800 SERIES

WIRELESS

TRANSMITTERS

2-WAY

WIRELESS

KEYPAD

(e.g. 5804BD)

OR

5800RL 2-WAY

RELAY MODULE

5883-003-V0

2-WAY

TRANSMISSION

MOUNT THE MODULE OR PC BOARD

The 5883 can be mounted remotely, or, with some controls, can be mounted inside the control's cabinet.

When mounting, make sure the antennas do not touch any metal surfaces.

First, Check for RF Interference:

Before mounting permanently,

use the red RF Interference LED (see figure 3) to check for strong

local radio frequency interference at the intended mounting location.

If this LED is continuously lit, the 5883 module should be relocated.

Removing the Cover

Remove the 5883's cover by inserting and twisting a screwdriver blade

in the slot at the center of the cover's lower edge.

Replace the cover when installation is complete if unit is not mounted

within a cabinet.

Mounting inside the control's cabinet

(refer to Fig. 2):

1. Remove the 5883’s circuit board from its base by bending back the

two flexible plastic tabs that hold the board's lower edge. Discard

the 5883's unused plastic cover and base.

2. In the control's cabinet, unfasten and move the control circuit board

downward (if already installed).

3. Hang two short (black) mounting clips (provided) on the raised

cabinet tabs in the cabinet, as shown in Detail B of Figure 2.

4. Insert the top of the 5883’s board into the supporting slots at the top

of the cabinet (Detail A). Swing the bottom of the board into the two

short (black) mounting clips installed in step 3, and secure it to the

cabinet with the accompanying screws. See Detail B.

5. Insert the top of the control’s board into the slot in the black clips

holding the lower edge of the 5883 board (see Detail B); position two

long (red) clips at the lower edge of the board (see Detail C).

6. Swing the lower edge of the control board into place, and secure with

two additional screws.

7. Insert the grounding lugs (provided) through the top of the cabinet

and into the left-hand terminals of the antenna blocks (at the upper

edge of the 5883's circuit board). Secure it to the cabinet with the

two screws provided. See Detail D.

8. Insert the 5883’s two antennas through the two openings in the top

of the cabinet, one into each block’s right-hand terminal, and tighten

the screws to secure them.

9. Affix the 5883's Summary of Connections label to the inside of the

control's cabinet door.

MOUNTING

CLIP

CABINET

DETAIL D

ANTENNA AND GROUNDING LUG INSTALLATION

ANTENNA

MOUNT

(2 PLACES)

ANTENNA

(2)

SCREW

(2)

MOUNTING

CLIP

CONTROL

CIRCUIT

BOARD

BOARD

SUPPORTING

SLOTS

HOLES FOR ANTENNAS

AND GROUNDING LUGS

RECEIVER CIRCUIT BOARD

(See Detail D)

++

++

RCVR BRD

DETAIL A

SIDE VIEW

OF BOARD

SUPPORTING SLOTS

DETAIL B

SIDE VIEW

OF MOUNTING

CLIP

DETAIL C

SIDE VIEW

OF MOUNTING

CLIP

GROUNDING

LUG

(2)

pcb_RF_mount-V0

CIRCUIT BOARD

CABINET

Figure 2. Installing the 5883 Board in the Control’s Cabinet

(Check the control’s Installation and Setup Guide for applicability.)

Mounting the 5883 remotely

NOTE: If mounting the 5883 in its own enclosure, the supplied PCB

mounting clips, grounding lugs, and screws are not needed.

1. All wiring between the 5883 and the control panel must be located

in a conduit.

2.

For concealed wiring, route wires through the rectangular opening at

the rear of the base before mounting. For surface wiring entry, a thin

breakaway area is provided along the base's right edge.

3. Mount the module in the selected location. For greatest security,

use all four mounting holes (two keyslot holes and two round holes)

in the plastic base. (Refer to Detail D in Figure 2 above.)

4. Install each antenna in the respective right-hand terminal of the

two terminal blocks at the upper edge of the 5883’s circuit board,

and tighten the screws to secure them.

5. Affix the 5883's Summary of Connections label to the inside of the

housing cover.

Fi

g

ure 1. Block Dia

g

ram