• Home
• Brands
• Honeywell Manuals
• Honeywell ADEMCO 6150RF
• Honeywell ADEMCO 6150RF Installation And Setup Manual

Honeywell ADEMCO 6150RF Installation And Setup Manual

Download Installation and setup manual of Honeywell ADEMCO 6150RF Keypad, Security System for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

- 3 -

An example of an installation using two 6150RF

Keypad/Transceivers with 2-Way Wireless Devices (e.g.,

5828V) on Two Partitions is shown below:

Settings 6150RF #1 6150RF #2

Keypad: Must be assigned to

Partition 1 in the

control panel

Must be assigned to

Partition 2 in the

control panel

House ID: Match Partition 1

House ID in the

control panel and

House ID in Wireless

Device

Match House ID in

Wireless Device

House ID

Source:

System Local

Receiver

Enable:

On Off

Transmitter

Enable:

On On

PROGRAMMING THE 6150RF

The 6150RF is shipped with pre-programmed default

values. Later in these instructions are diagrams showing

the wireless keys' loops and their default functions.

Regardless of which wireless key you use (even if it is one

not shown), loops 1-4 are defaulted for all eight devices as

shown. These values may be changed to suit the

installation.

Entering Program Mode

Press the [1] and [3] keys simultaneously for a few seconds,

within 30 seconds after applying power. The keypad beeps

three (3) times, and two dashes and two zeroes flash

alternately in the upper left-hand corner of the display. If

any other numbers or letters flash in the display, press the

[✻] key.

Note: The keypad will not enter programming mode if the system

has been armed before the 6150RF was powered up or

down.

Pressing the [1] and [3] keys 30 seconds or more after

applying power allows you to enter the User mode. This mode

allows you to enable and disable individual local wireless keys

(useful if, e.g., a user accidentally loses a wireless key). Refer

to the User Guide for instructions.

Programming Operations

Once you have entered the Program mode, you may move to

any program address simply by entering the program

address number. The 6150RF will automatically exit the

Program mode if no keys are pressed for 90 seconds. While

in the Program mode:

• Pressing the [✻] key stores the information displayed,

then moves you to the next prompt, and the keypad beeps

twice.

• Pressing the [#] key erases the current information and

moves you back so you may enter the correct information.

Enter a program address (e.g., press [1] for Keypad

Address; [2] for Receiver Address) to set the parameters in

the 6150RF.The following chart lists the program addresses,

the keypad display, and the choices.

Program

Address

Description Display Choices Default

1 Keypad Address cA 01-31 31

2 Receiver Address rA 00-30 00

3 House ID HI 01-31 10

4 House ID Source hS 1 = System

0 = Local

1 System

5 Wireless Key Editing d- Enter Existing Device Number

6 Receiver Enable rE 1 = On 0 = Off 1 Enable

7 Transmitter Module Enable tE 1 = On 0 = Off 1 Enable

8 Wireless Key Auto Enroll d* Enter Serial Number

8 then 2 Wireless Key User Code u4 Enter 4-Digit User Code

8 then 4 Wireless Key Loop Function Ln Enter Loop Number then Function

(See Wireless Key Function Chart)

Loop 2 1 (Disarm)

Loop 3 2 (Arm Away)

Loop 4 3 (Arm Stay)

8 then 5 Wireless Key On-Board Relay

Assignment

o- Enter Loop Number then Relay

Action

Loop 1 Close for 2 Seconds

9 Restore Defaults EE 1 = Restores Defaults

Any Other Key = Does Not

Restore Defaults

0 High Security Mode✝ En 1 = Enable; 0 = Disable 0 Disable

* The keypad will display the next number that can be enrolled (i.e., “d3”)

✝ When operating the system in High-Security mode, non-encrypted wireless keys will not function.

CONTROL

PANEL

6150RF

#1

6150RF

#2