• Home
• Brands
• Honeywell Manuals
• Honeywell ADEMCO 6150RF
• Honeywell ADEMCO 6150RF Installation And Setup Manual

Honeywell ADEMCO 6150RF Installation And Setup Manual

Download Installation and setup manual of Honeywell ADEMCO 6150RF Keypad, Security System for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

K4460-1V6 2/06 Rev B

ADEMCO 6150RF

ADEMCO 6150RFADEMCO 6150RF

ADEMCO 6150RF

Keypad/Transceiver

Keypad/TransceiverKeypad/Transceiver

Keypad/Transceiver

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The 6150RF Keypad/Transceiver is a combination unit incorporating a normally-open relay output and the functions of:

• 6150 Fixed Addressable Keypad

• 5881M RF Receiver

• 5800TM Transmitter Module

The 6150RF Keypad/Transceiver may be used on any control panel that supports the 6150 Keypad.

Wireless Features

The 6150RF supports the following:

• 5828/5828V wireless keypads.

• Up to eight wireless keys locally (programmed directly into

6150RF) without occupying any zones supported by the control

panel.

• Button-type transmitters (e.g., 5804, 5804BD) for local operation.

• A maximum of 16 transmitters programmed into any 5800

Series-supported control panel.

• Wireless keys with high-security (e.g., 5804E).

• RF jam detection when the receiver is enabled.

• Low-battery indications for the local wireless keys.

• A nominal range of 200' for the RF transmitters (some

transmitters have a shorter range).

• Wireless keys for control panels that do not support RF

themselves (such as 4110DL).

• Sends status signals (Armed, Ready, etc.) to bi-directional

units such as 5804BDV and 5828/5828V.

U

UU

U

L

LL

L

The 5802, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819BRS, 5819WHS, 5828/5828V and 5850

transmitters are not intended for UL installations.

Programming Features

• Auto Enroll mode for programming wireless keys.

• Provides a method for deleting a serial number and re-enrolling a new one in its place.

• Provides default settings for the wireless key functions.

Additional Features

• Operates the on-board relay in conjunction with the receiver (e.g., to trip a garage door opener).

U

UU

U

L

LL

L

This feature is not intended for UL installations.

• Activates relays programmed into the control panel.

• Provides an End User mode to enable/disable local wireless keys (e.g., if a user accidentally loses a wireless key). Refer to the

6150RF User Guide for this procedure.

INSTALLING THE 6150RF

Locate the 6150RF in an area and at a height where it is

convenient for user operation. The 6150RF must be at least

10 feet from the control panel to ensure proper operation of

the RF receiver. Perform the following steps to install the

6150RF.

1. Push the two case release snaps at the bottom of the

keypad with the blade of a medium screwdriver (this will

push in the release snap), then pull that side of the case

back away. Insert the screwdriver in the side of the

keypad (between the front and back case) and gently

twist to release the side locking tab. Repeat for the other

side. Refer to Figure 1 for location of the case back

release snaps and locking tabs.

2. Route the wiring from the control panel through the

opening in the case back. (See the control panel’s

instructions for proper wire run lengths.)

3. Mount the case back directly to a wall or electrical gang

box.

4. Connect the power and data wires from the control panel

to the terminals on the 6150RF as indicated in the

wiring table adjacent to Figure 2.

5. Connect the wires for the relay output (if used) to the

terminals on the 6150RF’s PC board.

6. Reattach the keypad to its case back.

Note: Upon power-up or exit of the Program Mode, the 6150RF

alternately flashes "Ad" and the 2-digit keypad address and

the 2-digit receiver address on the display. Press any key to

display the system status.

NOTE:

TO REMOVE CASE BACK

PUSH IN THE TWO MOUNTING

SNAPS LOCATED ALONG THE

BOTTOM OF THE KEYPAD

AND LIFT UP.

6150-006-V0

RETAINING

SNAPS

ARMED

READY

LOCKING

TA B

Figure 1 – Removing the 6150RF Case Back