Atma-Sphere MA-1 Quick Setup And Operation Instructions

Download Quick setup and operation instructions of Atma-Sphere MA-1 Amplifier for Free or View it Online on All-Guides.com.

Brand: Atma-Sphere

Category: Amplifier

Type: Quick setup and operation instructions

Model: Atma-Sphere MA-1 , Atma-Sphere Mk.II.2

Pages: 3 (0.13 Mb)

Download Atma-Sphere MA-1 Quick setup and operation instructions

Atma-Sphere MA-1 Quick setup and operation instructions - Page 1
1
Atma-Sphere MA-1 Quick setup and operation instructions - Page 2
2
Atma-Sphere MA-1 Quick setup and operation instructions - Page 3
3
ATMA-SPHERE MUSIC SYSTEMS, Inc.
160 So. Wheeler
St. Paul, MN 55105
Phone: 651-690-2246
FAX: 651-699-1175
http://www.atma-sphere.com
MA-1 Mk.II.2 amplifier quick setup and operation instructions
Installation:
Emplace the amps in your system. Connect the preamp cable to the appropriate input
connector on the front of the amp. If you must use the RCA input connector, make sure the shorting plug is
installed between pins 1 & 3 on the XLR connector else a buzz will result. Verify that both power switches
are OFF and connect AC power to the AC input connector on the rear of the amp. Connect the negative
speaker cable to the negative output terminal and the positive speaker cable to the positive output terminal.
Setup:
Install the tubes in their sockets. The front group of four sockets (no cooling holes) take the
6SN7GT driver tube. All other sockets take the 6AS7G output tube. A total compliment of four driver and
fourteen output tubes are required per each chassis. Engage the main power switch (edge of chassis) and
verify that the amber indicator lights. In about 15 seconds, the filaments of all tubes should be visibly
glowing orange. Rotate the BIAS control (beside the input connectors) fully counterclockwise. Wait at least
one minute, then engage the standby switch (other big toggle switch) and verify that the red indicator lights.
The amplifier is now fully powered up.
Bias adjustment:
Initially, rotate the Bias control (next to the input connector) fully
counterclockwise. Depress both the Test/Operate switch (edge of chassis opposite the power switches)
and the Bias Test switch (next to the Test/Operate switch) and the meter will rise to indicate the bias
reading. Use the Bias control (next to the input connectors) to set the meter as follows: Cold amp = .650A /
Hot amp (final setting) = .750A. Release the Bias Test switch as soon as you have made your adjustment.
If the amp is biased when cold, you can expect the bias to increase notably as it warms up, thus the
difference in settings between cold and hot. Check bias on a new amp daily until it has stabilized, typically
after 10-20 hours of use. When bias has stabilized it can be expected to stay in adjustment for extended
periods.
DC Offset adjustment:
Depress the Test/Operate switch (at the edge of the chassis, opposite the
status indicators). Examine the reading on the bias meter. If it is NOT zero (above OR below) adjust the DC
offset control (closest to the bias test switch) to bring the meter to a zero reading. The bias and DC offset
controls interact somewhat, so the bias and DC Offset procedures must be repeated.
Operation:
The amplifier is now completely operational. The amplifier can be left in either standby
or operational mode indefinitely. We recommend using the Standby feature if you are not listening to the
amp.
Fuses:
The first fuse by the power cord entry is the Output section B+ and is 5 Amp Slow (2.5A
slow for 235V). The middle fuse is the filament fuse and is 5 Amp Slow (2.5A for 235). The last fuse
controls the driver circuit and is 1 Amp slow (.5A Slow for 235 Volt). WARNING! To avoid fire hazard,
always replace fuses with same type and rating.
©1999 Atma-Sphere Music Systems Inc. 160 So. Wheeler St.Paul, MN. 55105 651.690.2246 / fax 651.699.1175