Honeywell HCD95534 Quick Install Manual

Download Quick install manual of Honeywell HCD95534 Digital Camera, Security Camera for Free or View it Online on All-Guides.com.

Honeywell HCD95534 Quick install manual - Page 1
1
Honeywell HCD95534 Quick install manual - Page 2
2
Document 800-00813 Rev A 11/08
HCD95534/X Camera Quick Install Guide
Important Safety Information
Read and keep these instructions.
Heed all warnings and follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
Installation
The HCD95534/X camera is designed for installation on a wall or ceiling. The
HCD95534/X is weather sealed for indoor or outdoor locations.
Attaching the Camera
1. Position the camera to the desired mounting location on a solid, flat surface (for
example, a crossbeam).
2. Using the supplied mounting template, mark the four screw holes for installation
and screw in the camera.
The mounting bracket can be separated from the camera housing for easier
installation. This is done by unscrewing and removing the thumb screw on the bracket
(see Figure 1).
Figure 1 Mounting Bracket
Note To ensure a waterproof installation, the notch in the camera base that the
power and video connections exit through should be facing down.
Positioning the Camera
Caution Do not swivel and position the camera without the mounting bracket
firmly in place.
Loosen the thumb screws and move the camera into position. Swivel the camera to
capture the desired field of view. Tighten the thumb screws to set the position.
Lens Setup
Adjusting the Zoom and Focus of the Lens
The zoom and focus adjustment is accessible at the underside front end of the camera
housing.
Figure 2 Lens Controllerr
Use a flathead screwdriver to adjust the zoom and/or focus. To adjust the focus, turn
the focus screw counter-clockwise for near focus and clockwise for far.
Camera Settings
Camera Functions
Figure 3 Camera Controller
Connecting the Camera
1. Connect the BNC video output connector to the video-in connector on your
monitor or video recorder.
2. Connect the camera to a power supply appropriate for your installation (12 VDC
or 24 VAC).
Programming
OSD Menu Structure
The HCD95534X menu system consists of one main SETUP menu (see Figure 4) for
easy camera programming.
Press down on the SETUP (MENU) control (see Figure 3) to display the SETUP menu.
Figure 4 Menu Structure
thumb screw
water drain notch
Zoom adjustment screw
Focus adjustment screw
Legend
#Description
1 Video-test monitor output connector
2 LUX-level adjustment DIP switches. Only one switch should be on at a time. They
modify the point at which the lux threshold (level of light) changes the mode of
operation (color or B/W).
3 LED-level adjustment screw. Increase (turn clockwise) or lower (turn counter-
clockwise) the IR LED brightness in night (B/W) mode.
4 Camera OSD control (four position plus center push)
Press this control To do this
UP, DOWN Select a new item
LEFT, RIGHT Select a menu item
SETUP (MENU) Access a submenu
LED-LEVEL
VIDEO-TEST
LUX LEVEL
DOWN
UP
LEFT RIGHT
SETUP (MENU)
PUSH DOWN
1
3
4
ON
1 STEP
2 STEP
3 STEP
4 STEP
2
STEP Color to B/W (LED on) B/W to Color (LED off)
1 1112 lux 1213 lux
2 89 lux 1011 lux
3 67 lux 78 lux
4 13 lux 35 lux
SETUP
MENU
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
DSS
SPECIAL!
EXIT MENU
SETUP
MENU
<<SETUP MENU>>
LENS DC!
SHUTTER
WHITE BAL. ATW
BACKLIGHT OFF
AGC MIDDLE!
DNR MIDDLE
DSS OFF
SPECIAL!
EXIT MENU
! indicates submenus
1
2
3
4
5
6
7
8
9
DC! , VIDEO, MANUAL
FLK, ESC! , MANUAL
ATW, MANUAL! , AWC!
OFF, LOW, MIDDLE, HIGH
OFF, LOW! , MIDDLE! , HIGH!
OFF, LOW, MIDDLE, HIGH
OFF, AUTO
!