• Home
• Brands
• Haier Manuals
• Haier BKD60SS
• Haier WQP12-BFE Owner's Manual

Haier WQP12-BFE Owner's Manual

Download Owner's manual of Haier BKD60SS Dishwasher for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

11

12

.6.

GB

Turning on the Appliance

Starting a wash cycle







After having completed all of the installation steps in the preced-

ing paragraphs, turn on the water all the way and press the ON-

OFF button (A) located on the control panel. The "B" indicator

light will come on. At this point, the appliance is on but you must

wait a few seconds before programming the setting for the cycle.

Cancelling or modifying a cycle while underway







Premise : A cycle that is underway can only be modified if it has

only been running for a short time. Otherwise, the detergent may

have already been used, and the appliance mayhave already

drained the wash water. If this is the case, the detergent dis-

penser must be refilled (see the paragraph entitled, "Loading

the Detergent").

To modify a cycle that is already underway, press the ON-OFF

button (A), then all of the settings will be cancelled.

If you forget to load some of the dishes







The wash cycle can be interrupted by pressing the Start/Pause

button. You can then load additional dishes and turn the appli-

ance back on. The cycle will start where it left off.

Premise: After selecting the wash cycle as indicated in the para-

graph entitled, "Setting and Starting a Wash Cycle..." the delay

time can be set.

1/2 load Button

This button (see "close-up View - Control Panel", letter "C") make

it possible to wash dishes using only the upper rack if there are

not enough dishes for a full load. This will allow you to save on

water and eletrical energy. It can be used before setting any of

the wash cycles, except for the intensive cycle (if included in the

wash cycle table). Please keep in mind that the amount of deter-

gent should also be cut in half.

a) During the delay period, it is preferable not to change any of

the settings. If it is necessary, all of the settings must be cancelled

by pressing the ON-OFF button (A) to indicate that all of the set-

tings have been cancelled.

At this point, all of the steps for "Setting the Wash Cycle with a

delayed Start Time" and "setting and Starting a Wash Cycle" must

be repeated, following the instructions contained in the correspond-

ing sections.

b) If the door is opened during the delay period, the indicator will

blink and acoustic signal will sound, and the countdown will stop.

It will begin again when the door is closed .

At the end of the wash cycle







Six acoustic signal will indicate that the wash cycle has finished

and the cycle indicator light (H) for the cycle will begin to die out.

Turn off the appliance using the ON-OFF button. Turn off the

water supply to the appliance and open the door. Wait a few

minutes before unloading the dishwasher to avoid handling the

dishes and utensils while they are still hot and more susceptible

to breakage. They will also dry better.

Setting and Starting a wash Cycle

Select the desired cycle by pressing the selector button (G). Each

time the button is pressed, one of the "H" cycle indicator lights will

come on in succession. Choose the wash cycle you feel is most

appropriate for the type of dishes that need washing (consult the

wash cycle table contained in this manual, especially when first

using the appliance).

Press the Start/Pause button (I), and after a few seconds a short

acoustic sound will indicate that the wash cycle has begun and

can no longer be changed. If necessary, read the paragraph en-

titled "Cancelling or modifying a cycle while underway..."

Wash cycle Programme Light

The wash cycle is running and the cycle indicator light (H) for the

cycle will begin to blink.

By pressing the "E" button (see close-up view-'Control panel")

the start of wash cycle can be delayed for between 1 to 9 hours.

Each time the button is pressed, the display (F) will show the

number of hours for the delay period. Choose the amount of

time desired. When the appliance is started with "I" button, a short

acoustic signal will sound and the delay time on the display will

blink, indicating that the countdown has begun.

After the time has lapsed, the cycle will start.

NOTE:

Wash Cycle adjustment Buttons

Setting the Wash Cycle with a Delayed Start Time