Haier WQP12-BFE Owner's Manual

Download Owner's manual of Haier BKD60SS Dishwasher for Free or View it Online on All-Guides.com.

Brand: Haier

Category: Dishwasher

Type: Owner's manual

Model: Haier BKD60SS , Haier WQP12-BFE

Pages: 12 (0.36 Mb)

Download Haier BKD60SS Owner's manual

Haier BKD60SS Owner's manual - Page 1
1
Haier BKD60SS Owner's manual - Page 2
2
Haier BKD60SS Owner's manual - Page 3
3
Haier BKD60SS Owner's manual - Page 4
4
Haier BKD60SS Owner's manual - Page 5
5
Haier BKD60SS Owner's manual - Page 6
6
Haier BKD60SS Owner's manual - Page 7
7
Haier BKD60SS Owner's manual - Page 8
8
Haier BKD60SS Owner's manual - Page 9
9
Haier BKD60SS Owner's manual - Page 10
10
Haier BKD60SS Owner's manual - Page 11
11
Haier BKD60SS Owner's manual - Page 12
12
.10.
GB
Positioning the Appliance
Position the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned on the right or the left to
facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screw them in
or out) to level the dishwasher. In any case, the appliance should
not be inclined more than 2
. If the appliance is level, it will help
ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) con-
nector and make sure that it is fastened tightly in place (see Fig.
1).
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there
is a risk that the water inlet can get blocked and damage the
appliance.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply of
water in the event of a problem with the water supply hose, or
leaks within the unit, in order to prevent damage to your home. If
for any reason the box containing the electrical components hap-
pens to get damaged, remove the plug for the appliance from the
socket immediately. In order to guarantee that the anti-flooding
feature operates properly, the "A" box with water supply hose must
be attached to the water supply tap as shown in Fig.1. No other
type of connection is acceptable. The water supply hose must not,
under any circumstances, be cut, as it contains electrical parts
which are live. If the length of the hose is not adequate to make a
proper connection, the hose must be replaced with one which is
long enough. This hose is available upon request from specialised
retailers and service centres.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see Fig.2). The free end of the hose must be at
a height between 40 and 100 cm and must not be immersed in
water.
Attention:
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water
to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is sized for the maximum voltage on
the rating plate, insert the plug into an electrical socket which
is earthed properly (the earthing of the appliance is a safety
requirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug, replace the plug, rather than
using adpators or the like as they could cause overheating and
burns.
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system, heating system), as
long as it does not exceed a temperature of 60.
In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
Fig.2
Fig.1
Installation