GE JKP90BM4BB Installation Instructions

Download Installation instructions of GE JKP90BM4BB Oven for Free or View it Online on All-Guides.com. This version of GE JKP90BM4BB Manual compatible with such list of devices, as: JKP90BM4BB, PK916SR3SS, PK956DR3WW, PT900SR2SS, PT920DR2BB

GE JKP90BM4BB Installation instructions - Page 1
1
GE JKP90BM4BB Installation instructions - Page 2
2
GE JKP90BM4BB Installation instructions - Page 3
3
GE JKP90BM4BB Installation instructions - Page 4
4
Installation Instructions
27"& 30"Electric Built-InWall Ovens
Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
° IMPORTANT -- Savethese
instructions for local inspector's use.
° IMPORTANT -- Observe all
governing codes and ordinances.
Note to Installer- Be sure to leave these
instructions with Consumer.
Note to Consumer- Keep these
instructions for future reference.
Skill level - Installation of this appliance
requires a qualified installer or electrician.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under Warranty.
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
FOR YOUR SAFETY:
^,u,WARN ING: Before beginning the installation, switch power off at the service
panel and lock the service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb,
sit, stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2" Conduit
36" (91 cm) of String
TOOLS YOU MAY NEED
1/8" Drill Bit and Electric or Hand Drill
Phillips Screwdriver
Wire Strippers
[_ REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all
packing parts from oven, racks and heating elements. Remove protective film and labels on the
outer door and control panel. Also, remove plastic on trims and panel, all tape around the oven
and any shipping screws securing the oven to the base pad. Open oven door and remove
literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be
installed at the end of the installation process. The trim is wrapped separately and taped
to the top of the unit.
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may
also be installed below a countertop or below specified cooktops. See the label on top of the oven for
approved models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of
the oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific
requirements.
E_ PREPARE THE OPENING (FOR INDOOR USE ONLY)
NOTE: If the cabinet does not have a solid bottom,
two braces or runners must be installed to support
the weight of the oven. For single ovens, the runners
and braces must support 200 Ibs (91 kg). For double
ovens, the runners and braces must support 375 Ibs.
(170 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary
to add wood shims under the runners and front trim
until the marks or opening are covered.
NOTE: If the cabinet does not have a front frame
and the sides are less than ¾" (1.9 cm) thick, shim
both sides equally to establish the cutout width.
2" x4"(5cmxtOcm)
or Equivalent Runners Level
with Bottom of Cutout
Suitable
Bracing
to Support
Runners
I 21 5/8"
(54.9 cm) Over /
Centerline
of Cabinet
r21rA-i CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick,
shim both sides equally to establish the cutout width.
H
I
These ovens are not I
approved for stackable
I
installations.
Side-by-Side Installations (30" only) " - -- - - -.
Install two ovens in separate cutouts,
Center Line Center Line
I I
I 30.5" (77.5 cm) I
! !
I
Cutout
observe all
dimensions and
requirements,
I
Cutout 1
observe all
dimensions and
requirements,
I-4[,-- 2" (5,1 cm) Min,
*--- B --.
Wails Must
Be at Least
28 1/2"
(72.4 cm)
Junction Box
Location
(junction box
may be
located
in adjacent
cabinet)
22" (55.9 cm)
C Min. To
Bottom of
Junction Box
Recommended
u
Cutout
Location
From Floor
32 t12" (82.8 cm)
Cutout Depth - 23 t/2"
(59,7 cm) Minimum
Dimension Dimension Description 27" Single Oven 30" Single Oven
A Cabinet Width 27" (68.6 cm) 30" (76.2 cm)
B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min.
25¼" (64.1 cm) max. 28%" (72.7 cm) max.
C Cutout Height 27%" (70.2 cm) min. 27¼" (69.2 cm) min.
28½" (71.4 cm) max. 27%6" (69.4 cm) max.
D Overlap of Oven Over 1" (2.5 cm) _½6"(1.75 cm)
Side Edges of Cutout
E Clearance to 20" (50.8 cm) min. 21" (53.3 cm) min.
Adjacent Corners,
Drawers, Walls, etc.,
When Door Is Open
F Overlap of Oven 1" (2.5 cm) min. 1" (2.5 cm) min.
Top of Cutout
G Overlap of Oven 1" (2.5 cm) min. 1¼" (3.2 cm)
Bottom of Cutout
H Junction Box Location 8%" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
12-11-B-ICUTOUTFORSINGLE OVENS-UNDER COUNTER
NOTE: These ovens are only approved to be installed under the specific models as labeled on
the unit.
Gas or Electric Cooktops May Be installed Over This Oven.
See Cooktop Installation instructions for Cutout Size, 240V/208V
See Label on Top of Oven for Approved Models, Junction Box
Location (junction
box may be
in adjacent cabinet)
25" (63.5 cm)
Gas and Electrical Connections
for Gas Cooktop Must be Located
in an Ad acent Accessible
Locat on to the Right
MUST SUPPORT 200 Ibs. (90 kg) FOR SINGLE OVENS
MUST SUPPORT 375 Ibs, (170 kg) FOB DOUBLE OVENS
Cutout - observe
all dimensions and
requirements.
Side-by-Side Installations (30" only)
Install two ovens in separate cutouts.
Center Line Center Line
30.5" (77.5 cm) I
',_ _I
I
I
I
I
Cutout- observe I
all dimensions and
I
requirements.
'_1 I_ 2" (5,1 ore) Min,
22" (55.9 cm) Min. 36" (91.4 crn)
Above Support
Platform Countertop
Height
4" (t0.2 cm)
Toeklck
NOTE: One cooktop may be centered over either
oven in the side-by-side installation.
Dimension Dimension Description 27" Single Oven 30" Single Oven
A Cabinet Width 25" (63.5 cm) min. 28½" (72.4 cm) rain.
25¼" (64.1 cm) max. 28%" (72.7 cm) max.
B Cutout Height 27%" (70.2 cm) min. 27¼" (69.2 cm) min.
28½" (71.4 cm) max. 27%6" (69.4 cm) max.
C Unit Overlap Top 1" (2.5 cm) 1" (2.5 cm)
D Unit Overlap Bottom 1" (2.5 cm) 1¼" (3.2 cm)
E Unit Overlap Side Edges 1" (2.5 cm) _6" (1.75 cm)
F Junction Box Location 8¾" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
Continue to Section 3.
_--]_"] CUTOUT FOR DOUBLE OVENS (2 ThermalOvens)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick,
shim both sides equally to establish the cutout width.
--_
H
_- F
G"
................A_ i _
Junction Box
Location
(junction box
may be
located
J in adjacent
cal_inet)
eli
Dimension Dimension Description 27" Double Oven 30" Double Oven
A Cabinet Width 27" (68.6 cm) 30" (76.2 cm)
B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min.
25¼" (64.1 cm) max. 28%" (72.7 cm) max.
C Cutout Height 49_6 '' (126.2 cm) min. 51_%6'' (131.6 cm) min.
50½" (127.3 cm) max. 51_%6'' (131.9 cm) max.
D Overlap of Oven 1" (2.5 cm) _6" (1.75 cm)
Over Side Edges
of Cutout
E Clearance to Adjacent 20" (50.8 cm) min. 21" (53.3 cm) min.
Corners, Drawers, Walls,
etc., When Door Is Open
F Overlap of Oven 1" (2.5 cm) min. 1" (2.5 cm) min.
Top of Cutout
G Overlap of Oven 1" (2.5 cm) min. 1¼" (3.2 cm)
Bottom of Cutout
H Junction Box Location 8¾" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
J Height to Bottom of 44" (111.8 cm) 47" (119.4 cm)
Junction Box
K Recommended 13¼" (33.7 cm) 12" (30.5 cm)
Cutout Location from
Floor
Continue to Section 3.
E_[_] CUTOUT FOR DOUBLE OVENS (with UpperMicrowaveOven)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick,
shim both sides equally to establish the cutout width.
H
Junction BOX
Location
/ (junction box
/ may be
located
in adjacent
cabinet)
C 28" (71.1 cm) Min.
to Bottom Of
. -" Cutout Depth = 23 1/2"
_.........__,_/(59.7 cm) Minimum
Cutout Location I
From Floor
A
Dimension 27" Oven 30" Oven
Dimension Description with Microwave with Microwave
A Cabinet Width 27" (68.6 cm) 30" (76.2 cm)
B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min.
25¼" (64.1 cm) max. 28%" (72.7 cm) max.
C Cutout Height 41½" (104.5 cm) min. 42%6" (107.2 cm) min.
41¼" (104.8 cm) max. 42¼" (107.3 cm) max.
D Overlap of Oven 1" (2.5 cm) _6" (1.75 cm)
Over Side Edges
of Cutout
E Clearance to Adjacent 20" (50.8 cm) min. 21" (53.3 cm)
Corners, Drawers, Walls,
etc., When Door Is Open
F Overlap of Oven 1" (2.5 cm) min. 1" (2.5 cm) min.
Top of Cutout
G Overlap of Oven 1" (2.5 cm) min. 1¼" (3.2 cm)
Bottom of Cutout
H Junction Box Location 8¾" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
Continue to Section 3.
_--][_ CUTOUT FOR INSTALLATION OVER A WARMING
DRAWER
NOTE: Install the oven only with specific models listed on the label located on top of the oven.
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven
supports above the Warming Drawer location do not obstruct the required interior depth and
height.
When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ,
properly grounded receptacle must be installed. Refer to installation instructions packed with
the Warming Drawer for specific installation requirements.
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2" (5.1 cm)
Min.
Per Warming
Drawer
Requirement
Continue to Section 3.
31-10730-1 I 08-09 JR