• Home
• Brands
• Siemens Manuals
• Siemens WD14H520GB
• SIEMENS WD14H520GB Installation Maintenance Instructions

SIEMENS WD14H520GB Installation Maintenance Instructions

Download Installation & maintenance instructions manual of Siemens WD14H520GB Washer/Dryer for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

1

Safety instructions

 The washer dryer is heavy  take care when lifting it.

 Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas

where there is a risk of frost.

 The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer

door).

 In addition to the instructions mentioned here, special regulations of the relevant water and

power supply companies may apply.

 If in doubt, have the appliance connected by a technician.

 Lay hoses and cables in such a way that there is no risk that they can be tripped over.

Environmental disposal



 Dispose of packaging in an environmentally friendly manner.

 This appliance has been identified in accordance with the European Directive

2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive

specifies aâframework for the return and recycling of waste appliances and is valid

throughout Europe.

Scope of delivery

Humidity in the drum is caused

byâthe final inspection.

Depending on the connection

 Aâ2440 mm dia. hose clip may also be required for connecting the siphon (available from

specialist retailers). aPageâ4: Water connection

Useful tool

 Spirit level for aligning the washer dryer.

 Wrench for adjusting the machine feet.

Water drainage

Power cord

Water supply

Covers

Hose holder

Aqua-Stop Aqua-Secure Standard

2

Installation area

 Stability is important to prevent the machine from wandering.

 The installation area must be firm and level.

 Soft floors/floor coverings are not suitable.

 Ensure the area is well ventilated to achieve good drying performance.

If installing the appliance on a pedestal

 It is essential to secure the washer dryer feet with holding bracketsâ*.

If installing the appliance on a wooden joist floor

 If possible, install the washer dryer in a corner.

 Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.

 It is essential to secure the washer dryer feet with holding bracketsâ*.

*âorder no. WMZ 2200, WX 9756

Hose and cable lengths





Connection on left side or Connection on right side

Note: if hose holders are used, the hose lengths may be reduced.

Available from dealer/customer service:

 Aqua-Stop extension hoseâ**, approx. 2.50 m.

 Longer supply hose, approx. 2.20 m, for standard model.

**âorder no. WMZ 2380, WZ 10130

Built-under/Built-in appliance

Build-under/build-in before connection to the power supply.

Installed in between kitchen units (built-under or built-in)

 Dimension requirement of kitchen unit:

aâ=â650âmm, bâ=â620âmm, câ=â 850âmm

 Install washer dryer only under a continuous worktop that

is connected firmly to the adjacent cupboards.

 The installation area must be well ventilated, otherwise the

washer dryer will operate below optimum performance.

Dimension of ventilation cross-section:

d x e = 200 mm x 100 mm, f = 365âmm

Distance between wall and machine: 50âmm

~140 cm

~160 cm

~140 cm

~90 cm

~165 cm

~95 cm

max. 100 cm

min. 60 cm

f

e

3

Removing transport bolts

 Before using the appliance for the first time, always remove and retain

all 4 transport bolts.

 If transporting the appliance subsequently, always re-install the

transport bolts  this prevents damage to the machine. aPageâ6

 Retain the screw and sleeve.

1. Take the hoses out of the holder and the elbow.

2. Undo and remove all 4 transport bolts.

3. Take the power cord out of the holders. Remove the sleeves.

4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose

holders.

5. Fix the hoses in the hose holders.

4

Water connection



 Risk of electric shock! Do not immerse the Aqua-Stop safety device in water

(containsâanâelectric valve).

 To prevent leakage or water damage, follow the instructions in this chapter.

 Attention: operate the washer dryer with cold drinking water only.

Do not connect to the mixer tap of a pressureless hot-water heater.

 Do not use a used inlet hose. Only use the inlet hose supplied or one which

was purchased from an authorised specialist dealer.

 If in doubt, have the appliance connected by a technician.

Water supply

Water inlet hose:

Attention: do not kink, crush, modify or cut through (strength is no longer guaranteed).

Optimum water pressure in the mains: 1001000 kPa (110 bar)

 When the tap is turned on, the water flow is at least 8 l/min.

 If the water pressure is higher, install a pressure reducing valve.

Model: Aqua-Stop

Aqua-Secure

Standard

1. Connect the water supply hose to the tap.

Tighten plastic screw fittings by hand only.

2. Carefully turn on the tap and check that the

connection points are not leaking.

Attention: the screw connection is under

water mains pressure.

Water drainage

Water drainage hose:

Attention: do not kink or stretch.

Height difference between installation area and outlet: 60100 cm

Drainage into a sink/bath tub:

Attention: secure the drainage hose to prevent it from slipping out

ofâtheâsink.

Attention: the plug must not be in the plug hole. When the water is being

pumped out of the washer dryer, check that the water drains away quickly

enough. Do not immerse the end of the drainage hose in the water that has

been pumped out. There is a risk that water will be drawn back into the

washer dryer.

Drainage into a siphon:

Attention: secure the connection with a 2440 mm dia. hose clip (available

from a specialist retailer).

Drainage into a plastic pipe with rubber sleeve:

Attention: Secure the drainage hose to prevent it from slipping out

ofâtheâdrain.

3/4



min. 10 mm

max.

90°

max.

9

0°

3/4



min 10 mm

5

Manufacturer (see Operating instructions) 0810 / 9000 479252

Alignment

High levels of noise, intense vibrations and wandering may be due to incorrect alignment.

Alignment will be carried out by customer service or authorised technicians, if you want

toâalign the machine by yourself please use a spirit level.

Aligning the washer dryer with a spirit level.

1. Undo the lock nut in a clockwise direction using a wrench.

2. Adjust the height by turning the appliance foot.

All four appliance feet must be placed firmly on the floor.

The washer dryer must not be able to wobble.

Check the alignment of the washer dryer with a spirit level andâ

correct if necessary.

3. Tighten the lock nut against the housing.

Hold the foot in place and make sure that the height is not adjusted.

The lock nuts on all four appliance feet must be screwed tightly against

the housing.

Electrical connection

ʑ

Connect the washer dryer to an alternating current via a correctly installed earthed socket

only.

ʑ

The mains voltage and specifications on the washer dryer must match.

aPageâ6: Technical specifications

ʑ

For information about the connected load and required fuse.

aPageâ6: Technical specifications

ʑ

Ensure that:

 the mains plug and socket are compatible,

 the cable cross-section is adequate,

 the earthing system has been installed correctly.

ʑ

A damaged power cord may be replaced by an electrician only.

A replacement power cord is available from customer service.

ʑ

Do not use multiple plugs/connectors or extension cables.

ʑ

If a residual current operated circuit-breaker is used, use only a type which guarantees

compliance with the currently valid regulations.

ʑ

Mains plug:

 do not insert into/pull out of the socket with damp hands.

 do not pull the plug out of the socket by pulling on the power cord.

 never pull out the plug while the appliance is in operation.