GE GFDS355EL1MS Installation Instructions Manual

Download Installation instructions manual of GE GFDN120ED0WW Dryer for Free or View it Online on All-Guides.com. This version of GE GFDN120ED0WW Manual compatible with such list of devices, as: GFDN240EL0WW, GFDN245EL1MV, GFDS155ED0MS, GFDS350EL1WW, GFDS355EL1MG

GE GFDN120ED0WW Installation instructions manual - Page 1
1
GE GFDN120ED0WW Installation instructions manual - Page 2
2
GE GFDN120ED0WW Installation instructions manual - Page 3
3
GE GFDN120ED0WW Installation instructions manual - Page 4
4
GE GFDN120ED0WW Installation instructions manual - Page 5
5
GE GFDN120ED0WW Installation instructions manual - Page 6
6
GE GFDN120ED0WW Installation instructions manual - Page 7
7
GE GFDN120ED0WW Installation instructions manual - Page 8
8
GE GFDN120ED0WW Installation instructions manual - Page 9
9
GE GFDN120ED0WW Installation instructions manual - Page 10
10
GE GFDN120ED0WW Installation instructions manual - Page 11
11
GE GFDN120ED0WW Installation instructions manual - Page 12
12
GE GFDN120ED0WW Installation instructions manual - Page 13
13
GE GFDN120ED0WW Installation instructions manual - Page 14
14
Installation
Instructions
Electric Dryer
10
Questions on Installation? Call: 1-800-GECARES (US)
or Visit our Web site at: www.GEAppliances.com (US)
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IN PORTANT- savethese instructions
for local inspector's use.
IMPORTANT- Observe all governing
codes and ordinances.
Note to Installer - Be sure to leave these
instructions with the customer.
Note to Customer - Keep these instructions
with your Use and Care Book for future
reference.
Before the old dryer is removed from service
or discarded, remove the dryer door.
Service information and the wiring diagram
are located in the control console.
Do not allow children on or in the appliance.
Close supervision of children is
necessary when the appliance is used
near children.
Install the dryer where the temperature
is above 50°F for satisfactory operation of
the dryer control system.
ZkWARNING RISKOF FIRE
To reduce the risk of severe injury or death, follow all installation
instructions.
Clothes dryer installation must be performed by a qualified installer.
Install the clothes dryer according to these instructions and in
accordance with local codes.
This dryer must be exhausted to the outdoors.
Useonly rigid metal 4" diameter ductwork inside the dryer cabinet and use
only UL approved transition ducting between the dryer and the home duct.
DONOTinstall a clothes dryer with flexible plastic ducting materials. If
flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed
and installed in accordance with the instructions found in "Connecting
The Dryer To House Vent" on pages 4-5 of this manual. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct dryer airflow and increase the risk of fire.
Do not install or store this appliance in any location where it could be
exposed to water and or weather.
Save these instructions. (Installers: Be sure to leave these instructions
with the customer).
NOTE: Installation and service of this dryer requires basic
mechanical and electrical skills. It is your responsibility to
contact a qualified installer to make the electrical connections.
I
Step 1
Step 2
Step 5
Step 4
Step 5
Step 6
TOOLSYOU
WILL NEED
SLIPJOINTPLIERS
FLATBLADESCREWDRIVER
PHILLIPSSCREWDRIVER
MATERIALSYOUWILL NEED
4"DIA.METALDUCT
(RECOMMENDED)
)
4"DIA.FLEXIBLEMETAL(SEMI-RIGID)
ULLISTEDTRANSITIONDUCT
(IFNEEDED)
KITWXO8XIO077(INCLUDES2ELBOWS)
4"DIA.FLEXIBLEMETAL(FOILTYPE)
ULLISTEDTRANSITIONDUCT
(IFNEEDED.)
4"DUCT
%
4"DIA.METAL
ELBOWCLAMPS(2) EXHAUST
HOOD
OR
4"SPRING
CLAMPS(2)
SAFETY
GLASSES
_ 3/4"STRAIN
DUCTTAPE GLOVES RELIEF
ULRECOGNIZED
4"COVERPLATE(IFNEEDED
(KiTWEIM454)
DRYERPOWER
CORDKIT
(NOTPROVIDED
WITHDRYER)
ULRATED
120/240V,]OA
WITH30R4PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD.
Prepare the area and exhaust for installation of new dryer
(see section 1).
Check and ensure the existing external exhaust is clean (see
section 1)and meets attached installation specifications (see
section 5).
Remove the foam shipping pads (see section 1).
Move the dryer to the desired location.
Connect the power supply (see section 2).
Connect the external exhaust (see section 4).
Step 7 Levelyour dryer (seesection 5).
Step 8 Checkthe operation of the power supplyandventing.
Step9 Placethe ownersmanual and the installationinstructions in
a location wherethey will benoticed bythe owner.
Foralcoveor closetinstallation,seesection6.
Forbathroom or bedroominstallation,seesection7.
Formobileor manufacturedhome,seesection8.
Forsideor bottom exhaust,seesection9.
31-16629-1 03-11 GE
234D1052PO03