Samsung SC-152 User Manual
Download Operation & user’s manual of Samsung SC-152 CD/CDR Drive, CD Player for Free or View it Online on All-Guides.com.
Brand: Samsung
Category: CD/CDR Drive , CD Player
Type: Operation & user’s manual for Samsung SC-152
Pages: 2 (0.28 Mb)
1
2
1
Front View of the CD-ROM Drive
2
System Requirements
Rear View of the CD-ROM Drive
3
4 5
6 7
1
1
2
3
4
56
Headphone Connector
The sound output terminal enables you to plug stereo headphones into the drive.
It requires a 3.6 mm stereo mini-jack.
1
1
23 4 5
Digital output terminal
You can connect a sound card or MPEG card which support Digital output
terminal to your drive using this two-pin terminal.
1
Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the CD-ROM drive.
2
Remove the cover of your PC(main unit of the computer)
3
Remove the blank cover panel of the 5.25 inch unit in
which the CD-ROM drive is to be installed.
6
Put the cover back on your PC.
5
Install the CD-ROM drive into the unit and secure it with
mounting screws (recommended standard M3x6x4)
☛
◆
Depending on your PC model, you may need to
attach guide rails to the drive, so that the drive is
held firmly in place.
☛
◆
If you use screws that are longer than the
recommended standard, you may damage the
drive.
Before you install the CD-ROM drive, we strongly recommend that you make certain
that your set-up meets the system requirements listed below.
Installing the CD-ROM Drive
Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close
button is on the right.
To install the drive, proceed as follows.
2
Sound output terminal
You can connect a sound card to your drive using this four-pin terminal.
☛ This function is not covered in detail in this guide. Refer to the documentation
supplied with your sound card.
3
Master/slave select terminal
Usually, this is a pre-set configuration as illustrated below.
☛ Verify that the setting is as illustrated. If it is not, simply remove the jumper
and place it in the correct position.
4
Interface terminal
This input/output interface terminal is used to connect the 40-pin flat cable from
the IDE interface to the CD-ROM drive.
5
Power terminal
The power terminal is a four-conductor male plug.
Eject Button
3
Disc compartment
The compartment opens and closes automatically when you press
the Eject button.
6
Eject Button
4
Emergency eject hole
If the compartment does not open when you press the Eject button, power off
the computer, insert a pin or unfolded paper clip in the hole and push firmlhy)
2
Headphone volume control
This headphone volume control adjusts the volume for your headphones. You can only
use the headphone jack and volume control when you have installed the required
software utilities. For example, the Microsoft Windows Media player can be used.
5
LED
4
Connect the CD-ROM drive to the IDE interface and power
cables Iocated inside your computer.
☛ Connectors are keyed so it is impossible to put them in
an incorrect position. Do not force the connectors, if they
do not seem to fit.
Item
Windows version
MS-DOS version
Disk space
Free expansion unit
Type of computer
Description
Windows 95 OSR2 / 98 / 2000 / ME / XP
Windows NT 4.0 (or higher)
5.0(or higher)
100KB minimum
5.25 inch
IBM 486SX 20MHz (or higher) with an IDE interface
(or a 100% IBM-compatible computer)
CD-ROM DRIVE
SC-152
User's Guide - ENGLISH
Technical Specifications
Max. 7800KB/s
SC-152
SECTIONS
DISC
DRIVE PER -
FORMANCE
FRONT PANEL
REAR PANEL
OPERATING
ENVIRONMENT
GENERAL
RELIABILITY
ERROR RATE
Disc types supported
Disc diameter
Data transfer rate
Access time (
typical
)
Data buffer capacity
Laser
Slide mechanism
Spindle motor
Load mechanism
Button
Indicator(LED)
Headphone output
Volume control
Required power
Interface connector
Audio output
Jumper block
Work area
Storage area
Dimensions
SC-152L
SC-152A
Net weight
MTBF
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),
Video CD ready, Enhanced CD, CD-I/FMV, CD-R/RW
120mm or 80mm
PIO Mode - 4. DMA MW2, Ultra DMA(option)
75ms(typical)
128KB
Semiconductor Laser
Gear motor
Brushless motor
Tray, DC motor(Soft Eject)
Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits
Eject(Open/Close)
Busy
Stereo Mini - jack (Ø 3,6 mm) 0.60 ± 20% (Vrms) 33Ω
Dial type
+5V DC 1.3A, +12V DC 1.5A
ATAPI
Line out 0.70 ± 20%(Vrms), 47kΩ
Device configuration jumper
Temperature : 5~45 °C, Humidity : 8~80%
Temperature : -40~60 °C, Humidity : 5~90%
850g (set only)
125,000 POH(Duty 20%)
148.2 (W) x 42(H) x 202(D)mm
SAMSUNG continually strives to improve its products. Both the design
specifications and these user instructions are thus subject to change without
notice.
Dimensions
Net weight
740g (set only)
148.2 (W) x 42(H) x 184(D)mm
12 9
Safety Precautions
The following diagrams illustrate the precautions to be taken when using
your CD-ROM drive.
Setting Up the Device Driver
It is not necessary to set up additional device driver for Window
95/98/2000/ME/XP/NT because it uses the device driver provided by the
Window.
Solving Technical Problems
☛ Frictional sound detected during the operation of Spin-Up and Stop is made ABS
(Auto Balance System), not by malfunction.
◆
Automatic Setup
◆
Manual Setup
LAST DRIVE = Z
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
C :\SAMSUNG\MSCDEX /D:SSCD000
1Insert the setup diskette in the diskette drive and change the directory to A:,
where A: is the diskette drive.
To do so, type A: after the C:\ prompt and press [Enter].
2Type CDSETUP and press [Enter].
3Reboot the computer.
1Make the C:\SAMSUNG directory.
2Copy the files from the diskette to the C:\SAMSUNG directory.
To do so, type COPY A:
*
.
*
C:\SAMSUNG after the C:\ prompt and press
[Enter].
3Edit the CONFIG.SYS file.
Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.
4Edit the AUTOEXEC.BAT file.
Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.
5Reboot the computer.
You must not use the drive in any manner other than that specified in this guide.
Avoid exposing your eyes or skin to direct or scattered radiation.
CAUTION
Do not attempt to repair the CD-ROM drive yourself. Contact
your dealer or local SAMSUNG representative for all repairs.
If you make any adjustments or perform any operations other
than those specified in this guide, you run the risk of exposure to
hazardous radiation.
WARRANTY
Please refer to the Samsung limited warranty statements.
Precautions
1.To reduce the risk of fire or electric shock, do not expose
this appliance to rain or moisture.
2. Always check each disc for cracks before using it. If there are
cracks on the surfaces, especially around the border of the
center hole, we recommend that you make a copy of the disc
immediately and then stop using it. If you continue using the
disc, it will probably develop more cracks and eventually cause
irreparable damage.
3. Do not use poor quality discs:
● From unknown sources
● Without any copyright
● Scratched or damaged in any way
Problem
Meaning / Solution
The CD-ROM drive is not
detected by the computer.
◆ Check that the power, audio and IDE cables are
correctly connected to the computer.
◆ Change the IDE cable and reconnect it to the computer.
Preferably, connect a second IDE cable to the CD-ROM
drive in master mode.
◆ Check the position of the jumper in the master/slave
select terminal.
◆ Reinstall the device driver or update it with the latest
version by downloading it from the Samsung Web site.
- www.samsungodd.com
-
www.samsungelectronics.com
◆ This case may occur when there is a Windows
installation problem; reinstall Windows.
◆ Check whether the audio cable is correctly connected
to the sound output terminal on the CD-ROM drive and
the sound card CD-IN terminal.
◆ Check that the sound card is operational.
◆ Adjust the volume control.
◆ Install the latest version of the device driver.
◆ Check whether the CD is of good quality and clean it,
if necessary.
◆ Check that the power cable is correctly connected.
◆ Power off and disconnect the PC. Insert a pin or
unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
◆ Adjust the size of the replay screen.
◆ After checking the display resolution, adjust it, if
necessary.
◆ The computer may not recognize the disc if you start
playback too quickly after inserting the disc.
Open and close the disc compartment and try again.
◆ Clean the disc and try again.
◆ The interface mode of the sound card is AT-BUS.
You must therefore connect the CD-ROM drive to the
IDE port on the PC mother board, rather than to the
sound card, or install an IDE-compatible sound card.
After installing the CD-ROM
drive, the PC gets slower.
The CD-ROM drive is not
recognized by MS-DOS.
The CD-ROM drive is not
detected by Windows.
No sound is heard from an
audio CD.
A CD is not read or is read too
slowly.
The disc compartment will not
open.
When the MPEG software plays a
Video CD, the pictures are not regular
and the running speed is too slow.
The Disc is not in message is
displayed even though a disc
has been inserted.
The CD-ROM drive is not
detected after it is connected
to a sound card.
* The design of this product can be more or less changed according to its
characteristics.
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
✱ Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment
BG68-00326C Rev.00
http://www.samsungodd.com
www.samsungelectronics.com