• Home
• Brands
• Wilbur Curtis Company Manuals
• Wilbur Curtis Company PTTD-3
• Wibur Curtis Company PTTD-3 Instructions

Wibur Curtis Company PTTD-3 Instructions

Download Instructions of Wilbur Curtis Company PTTD-3 Small Kitchen Appliances for Free or View it Online on All-Guides.com. This version of Wilbur Curtis Company PTTD-3 Manual compatible with such list of devices, as: TCO-308, TCO-417, TCO-421, TCTD-35, TCTD-35S

1

2

3

4

FIND OUT MORE

ON

THE WEB.

WILBURCURTIS.COM

WILBUR CURTIS COMPANY

Montebello, CA 90640

1

F

IND OUT MORE

ON

THE WEB.

WILBURCURTIS.COM

MODELS INCLUDEDMODELS INCLUDED

MODELS INCLUDEDMODELS INCLUDED

MODELS INCLUDED

••

••

• TCTD-35

••

••

• TCTD-35S

••

••

• PTTD-3

••

••

• TCO-308

••

••

• TCO-417

••

••

• TCO-421

ISO 9001 REGISTERED

C

WARNING TO AVOID

SCALDING, Do not

remove brewcone while

brew light is flashing.

CAUTION: CAUTION:

CAUTION: CAUTION:

CAUTION: DO NOT

connect this brewer to

hot water. The inlet valve

is not rated for hot water.

CAUTION: CAUTION:

CAUTION: CAUTION:

CAUTION: Please use

this setup procedure

before attempting to use

this brewer. Failure to follow the

instructions can result in injury or

the voiding of the warranty.

WARNING HOT LIQUID,

Scalding may occur.

Avoid splashing.

Iced Tea Brewer Instructions

Curtis ADS System is Factory Pre-Set and Ready to Go… Right from the Carton.

Following are the Factory Settings for your Iced Tea Brewing System:

• Brew Temperature = 204°F • Dilution = 2 Gallon

• Concentrate = 1 Gallon • Drip Mode = 30 Seconds

System Requirements

• Water Source: 20 – 100PSI (Min Flow Rate of 1 GPM) • Electrical: See attached schematic for standard

model or visit www.wilburcurtis.com for your model.

SETUP STEPS

1. Place unit at counter height. on a firm, level base, in such a way that it can be connected to water and power supply.

2. Connect water line to inlet fitting on valve. Water pressure entering brewer is required to be stable and must provide

minimum of 1 gallon per minute. Use water regulator for constant pressure. Required water pressures, 20 to 100 psi.

2. Plug power cord into electrical outlet rated 20A.

3. Turn on toggle switch, behind unit. Heating tank will start filling. When the water reaches probe,heating element

turns on automatically.

4. Heating tank will require 20 to 30 minutes to attain operating temperature. READY TO BREW indicator will light at

this time.

5. Insert brewcone. Place empty tea container under brew cone. With water at operating temperature, run brew cycle,

without tea, for about 1 minute. This clears the water lines of air. Stop the brew cycle by switching off at ON/OFF

button. Discard water in tea container.

BREWING

INSTRUCTIONS

2. Slide brew cone into brew

rails. Place tea container

under brew cone.

3. Press the BREW button to

brew tea.

1. Place filter in brew basket.

Pour leaf tea into basket.

This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be

performed by an authorized Wilbur Curtis service center.

• Do NOT immerse the unit in water or any other liquid

• To reduce the risk of fire or electric shock, do NOT open top or front panel. No user serviceable parts inside.

Repair should be done only by authorized service personnel.

• Keep hands and other items away from hot parts of unit during operation.

• Never clean with scouring powders, bleach or harsh implements.

Important Safeguards/Conventions

ConventionsConventions

ConventionsConventions

Conventions

WW

WW

W

ARNINGS – ARNINGS –

ARNINGS – ARNINGS –

ARNINGS –

TT

TT

T

o help ao help a

o help ao help a

o help a

void personal injurvoid personal injur

void personal injurvoid personal injur

void personal injur

yy

yy

y

Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor

Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor

Important Notes/Cautions – from the factor

yy

yy

y

SanitaSanita

SanitaSanita

Sanita

tion Requirementstion Requirements

tion Requirementstion Requirements

tion Requirements

The National Sanitation Foundation requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for

cleaning underneath.

2. In some areas an approved backflow prevention device may be required between the brewer and the water supply.

Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.

FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO

WWW.WILBURCURTIS.COM

WW

WW

W

ILBURILBUR

ILBURILBUR

ILBUR

C C

C C

C

URTISURTIS

URTISURTIS

URTIS

C C

C C

C

OMPOMP

OMPOMP

OMP

ANYANY

ANYANY

ANY

, I, I

, I, I

, I

NCNC

NCNC

NC

..

..

.