Whirlpool WHES20 Data Sheet
Download Performance data sheet of Whirlpool WHES20 Water Dispenser, Water System for Free or View it Online on All-Guides.com.
Brand: Whirlpool
Category: Water Dispenser , Water System
Type: Performance data sheet for Whirlpool WHES20
Pages: 1 (0.06 Mb)
1
Demand Control Water Softeners Performance Data Sheet
Model WHES20 WHES30
Rated Service Flow Rate (gpm) 6.5 8.0
Pressure Drop at Rated Service Flow Rate (psi) 9.3 14.4
Rated Softening Capacity (Grains @ Salt Dose)
8,700 @ 1.7 lbs
16,400 @ 5.4 lbs
20,100 @ 9.1 lbs
14,700 @ 2.9 lbs
25,400 @ 8.0 lbs
30,100 @ 13.1 lbs
Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose) 5000 @ 1.7 lbs 5000 @ 2.9 lbs
Min.-Max. Working Pressure (psi) 20-125 20-125
Min.-Max. Operating Temperature (°F) 40-120 40-120
Max. Flow Rate (gpm) to Drain During Regeneration Cycle 2.0 2.0
These softeners conform to NSF/ANSI 44 for the specific performance claims as verified and substantiated by test data. These models are efficiency rated. The efficiency rating is
valid only at the stated salt dose. It has a demand initiated regeneration (D.I.R.) feature that complies with specific performance specifications intended to minimize the amount of
regenerant brine and water used in their operation. These softeners have a rated softener efficiency of not less than 3,350 grains of total hardness exchange per pound of salt (based on
sodium chloride) and shall not deliver more salt than its listed ratings or be operated at a sustained maximum service flow rate greater than its listed rating. This softener has been
proven to deliver soft water for at least ten continuous minutes at the rated service flow rate. The rated salt efficiency is measured by laboratory tests described in NSF/ANSI
Standard 44. These tests represent the maximum possible efficiency that the systems can achieve. Operational efficiency is the actual efficiency after the system has been installed. It
is typically less than the efficiency due to individual application factors including water hardness, water usage, and other contaminants that reduce the softener’s capacity.
IMPORTANT: Consult Installation and Operation Manual for California efficiency requirements. These systems are not intended for treating water that is microbiologically
unsafe or of unknown quality without adequate disinfection before or after the systems. For best results use clean grades of water softener salt. Refer to Installation and Operation
Manual for warranty or further details on installation and maintenance, user’s responsibility, parts and service, and any further restrictions, or limitations to the use of the product.
Manufactured and warranted by Ecodyne Water Systems
1890 Woodlane Drive
Woodbury, MN 55125
1-866-986-3223
05/26/11 (Rev. J)
7274058
Systems tested and certified by NSF International
against NSF/ANSI Standard 44 for hardness
reduction and efficiency.
System tested and certified by the Wate
r
Quality Association against CSA, B483.1.
Demand Control Water Softeners Performance Data Sheet
Model WHES20 WHES30
Rated Service Flow Rate (gpm) 6.5 8.0
Pressure Drop at Rated Service Flow Rate (psi) 9.3 14.4
Rated Softening Capacity (Grains @ Salt Dose)
8,700 @ 1.7 lbs
16,400 @ 5.4 lbs
20,100 @ 9.1 lbs
14,700 @ 2.9 lbs
25,400 @ 8.0 lbs
30,100 @ 13.1 lbs
Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose) 5000 @ 1.7 lbs 5000 @ 2.9 lbs
Min.-Max. Working Pressure (psi) 20-125 20-125
Min.-Max. Operating Temperature (°F) 40-120 40-120
Max. Flow Rate (gpm) to Drain During Regeneration Cycle 2.0 2.0
These softeners conform to NSF/ANSI 44 for the specific performance claims as verified and substantiated by test data. These models are efficiency rated. The efficiency rating is
valid only at the stated salt dose. It has a demand initiated regeneration (D.I.R.) feature that complies with specific performance specifications intended to minimize the amount of
regenerant brine and water used in their operation. These softeners have a rated softener efficiency of not less than 3,350 grains of total hardness exchange per pound of salt (based on
sodium chloride) and shall not deliver more salt than its listed ratings or be operated at a sustained maximum service flow rate greater than its listed rating. This softener has been
proven to deliver soft water for at least ten continuous minutes at the rated service flow rate. The rated salt efficiency is measured by laboratory tests described in NSF/ANSI
Standard 44. These tests represent the maximum possible efficiency that the systems can achieve. Operational efficiency is the actual efficiency after the system has been installed. It
is typically less than the efficiency due to individual application factors including water hardness, water usage, and other contaminants that reduce the softener’s capacity.
IMPORTANT: Consult Installation and Operation Manual for California efficiency requirements. These systems are not intended for treating water that is microbiologically
unsafe or of unknown quality without adequate disinfection before or after the systems. For best results use clean grades of water softener salt. Refer to Installation and Operation
Manual for warranty or further details on installation and maintenance, user’s responsibility, parts and service, and any further restrictions, or limitations to the use of the product.
Manufactured and warranted by Ecodyne Water Systems
1890 Woodlane Drive
Woodbury, MN 55125
1-866-986-3223
Systems tested and certified by NSF International
against NSF/ANSI Standard 44 for hardness
reduction and efficiency.
System tested and certified by the Wate
r
Quality Association against CSA, B483.1.
05/26/11 (Rev. J)
7274058