Whirlpool WTW4800X User Manual

Download Dimensional information of Whirlpool  WTW4800XQ Washer, Washer/Dryer for Free or View it Online on All-Guides.com. This version of Whirlpool  WTW4800XQ Manual compatible with such list of devices, as:  WTW5500XW,  WTW5700XL, WTW4800X, WTW4910X, WTW5640X

Whirlpool  WTW4800XQ Dimensional information - Page 1
1
Top-Loading Washer
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
WTW4900X, WTW5500X,
WTW5550X, WTW5600X,
WTW5640X, WTW5610X
WTW5700X, WTW4750Y,
WTW4800X, WTW4910X
WTW4950X,
Electrical: A 120 volt, 60 Hz., AC only, 15- or 20-amp,
fused electrical supply is required. A time-delay fuse
or circuit breaker is recommended. It is recommended
that a separate circuit serving only this washer be
provided.
Washer dimensions
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.
W10240509C
02/2012
For closet installation, with a door,
the minimum ventilation openings
in the top and bottom of the door
are required. Louvered doors with
equivalent air ventilation openings
are acceptable.
42"
(1067 mm)
27"
(686 mm)
27
1
/
2
"
(699 mm)
3"
(76 mm)
3"
(76 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
17"
(432 mm)
1"
(25 mm)
1"
(25 mm)
5"
(126 mm)
14" max.
(356 mm)
Dimensions show recommended spacing allowed, except for closet door ventilation
openings which are minimum required. This washer has been tested for installation with
spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of
installation and servicing, and spacing for companion appliances and clearances for walls,
doors, and oor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top and bottom air openings in
door are required.
DRAIN SYSTEM
Minimum diameter for a standpipe drain: 2" (51 mm).
Minimum carry-away capacity: 17 gal. (64 L) per minute.
Top of standpipe must be at least 39" (990 mm) high;
install no higher than 96" (2.44 m) from bottom of washer.
If you must install higher than 96" (2.44 m), you will need
a sump pump system.
Wall standpipe drain system
Laundry tub drain system
Minimum capacity: 20 gal. (76 L).
Top of laundry tub must be at least
39" (990 mm) above oor; install
no higher than 96" (2.44 m) from
bottom of washer.
IMPORTANT: To avoid siphoning,
no more than 4.5" (114 mm) of drain
hose should be inside standpipe or
below the top of wash tub. Secure
drain hose with cable tie.
Floor drain system
Floor standpipe drain system
See requirements for oor standpipe drain system.
30"
(762 mm)
4
1
/2"
(114 mm)
4
1
/
2
"
(114 mm)
4
1
/2"
(114 mm)
30"
(762 mm)
30"
(762 mm)
Floor drain system requires a Siphon Break Kit
(Part Number 285834), 2 Connector Kits (Part
Number 285835), and an Extension Drain Hose
(Part Number 285863) that may be purchased
separately. To order, please see toll-free phone
numbers in your Use and Care Guide. Minimum
siphon break: 28" (710 mm) from bottom of
washer. (Additional hoses may be needed.)