Delta 31-390 User Manual

Download Instruction manual of Delta 31-390 Sander for Free or View it Online on All-Guides.com.

Brand: Delta

Category: Sander

Type: Instruction manual

Model: Delta 31-390 , Delta 31-392

Pages: 16 (0.76 Mb)

Download Delta 31-390 Instruction manual

Delta 31-390 Instruction manual - Page 1
1
Delta 31-390 Instruction manual - Page 2
2
Delta 31-390 Instruction manual - Page 3
3
Delta 31-390 Instruction manual - Page 4
4
Delta 31-390 Instruction manual - Page 5
5
Delta 31-390 Instruction manual - Page 6
6
Delta 31-390 Instruction manual - Page 7
7
Delta 31-390 Instruction manual - Page 8
8
Delta 31-390 Instruction manual - Page 9
9
Delta 31-390 Instruction manual - Page 10
10
Delta 31-390 Instruction manual - Page 11
11
Delta 31-390 Instruction manual - Page 12
12
Delta 31-390 Instruction manual - Page 13
13
Delta 31-390 Instruction manual - Page 14
14
Delta 31-390 Instruction manual - Page 15
15
Delta 31-390 Instruction manual - Page 16
16
ADDITIONAL SAFETY RULES FOR
ABRASIVE FINISHING MACHINES
1. DO NOT OPERATE THIS MACHINE UNTIL it is
assembled and installed according to the instructions.
2. OBTAIN ADVICE from your supervisor, instructor, or
another qualified person if you are not familiar with the
operation of this machine.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
4. USE THE GUARDS WHENEVER POSSIBLE. Check
to see that they are in place, secured, and working
correctly.
5. CHECK BELTS for wear and tension. If the belt is
damaged or can’t be tensioned properly, replace it.
6. CHECK FOR CORRECT BELT INSTALLATION, and
insure that the belt is tracking properly.
7. KEEP ARMS, HANDS, AND FINGERS away from
abrasive surfaces.
8. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a hand
to contact the sanding surface.
9. NEVER WEAR GLOVES or hold the workpiece with a
rag when sanding.
10. NEVER START THE MACHINE with the workpiece
against the sanding surface.
11. NEVER START THE MACHINE before clearing the
table of all objects (tools, scrap pieces, etc.).
12. MAINTAIN MINIMUM CLEARANCE between the
table and the sanding surface.
13. USE A BACKSTOP when using the belt finishing
machine in a horizontal position.
14. FEED THE WORKPIECE AGAINST THE
ROTATION OF THE SANDING SURFACE. Hold
the workpiece securely on the table.
15. USE A DUST COLLECTION SYSTEM.
16. CLEAN THE MACHINE AND DUST
COLLECTION SYSTEM THOROUGHLY BEFORE
AND AFTER SANDING METAL. Combining wood
dust and metal filings (or aluminum filings and
metal filings) can create a fire hazard. DO NOT
sand magnesium. It is highly flammable.
17. FOR DRUM SANDERS, DO NOT SAND
WORKPIECES SHORTER THAN 7" or thinner
than 1/32".
18. PROPERLY SUPPORT LONG OR WIDE
workpieces.
19. DISCONNECT THE MACHINE from the power
source before installing or removing accessories,
before adjusting or changing set-ups, or when making
repairs.
20. DISCONNECT THE MACHINE from the power
source, and clean the table/work area before leaving
the machine. LOCK THE SWITCH IN THE “OFF”
POSITION to prevent unauthorized use.
21. ADDITIONAL INFORMATION regarding the safe and
proper operation of this machine is available from the
Power Tool Institute, 1300 Summer Avenue,
Cleveland, OH 44115-2851. Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please refer
to the American National Standards Institute ANSI
01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
3
SAVE THESE INSTRUCTIONS.
Refer to them often
and use them to instruct others.