Delta 31-250 User Manual

Download Instruction manual of Delta 31-250 Sander for Free or View it Online on All-Guides.com.

Brand: Delta

Category: Sander

Type: Instruction manual for Delta 31-250

Pages: 24 (3.48 Mb)

Download Delta 31-250 Instruction manual

Delta 31-250 Instruction manual - Page 1
1
Delta 31-250 Instruction manual - Page 2
2
Delta 31-250 Instruction manual - Page 3
3
Delta 31-250 Instruction manual - Page 4
4
Delta 31-250 Instruction manual - Page 5
5
Delta 31-250 Instruction manual - Page 6
6
Delta 31-250 Instruction manual - Page 7
7
Delta 31-250 Instruction manual - Page 8
8
Delta 31-250 Instruction manual - Page 9
9
Delta 31-250 Instruction manual - Page 10
10
Delta 31-250 Instruction manual - Page 11
11
Delta 31-250 Instruction manual - Page 12
12
Delta 31-250 Instruction manual - Page 13
13
Delta 31-250 Instruction manual - Page 14
14
Delta 31-250 Instruction manual - Page 15
15
Delta 31-250 Instruction manual - Page 16
16
Delta 31-250 Instruction manual - Page 17
17
Delta 31-250 Instruction manual - Page 18
18
Delta 31-250 Instruction manual - Page 19
19
Delta 31-250 Instruction manual - Page 20
20
Delta 31-250 Instruction manual - Page 21
21
Delta 31-250 Instruction manual - Page 22
22
Delta 31-250 Instruction manual - Page 23
23
Delta 31-250 Instruction manual - Page 24
24
3. Use a 9/16” socket with an extension (not supplied).
Place it in one of the two holes where the hole plugs were
removed. Loosen one hex bolt, then the other to relieve
tension on the motor. (One is shown at (D) Fig. 26). Apply
upward pressure on the motor (located under the machine)
to relieve tension on the belt. Replace or change the belt
positions on the pulleys. IMPORTANT: When the belt is on
the inner pulleys (F) Fig. 26, the sanding drum speed is 3300
SFM. When the belt is positioned on the outer pulleys (G)
Fig. 27, drum speed is 2210 SFM. NOTE: Position the poly-
v drive belt on the pulleys correctly to provide maximum
performance with minimal belt wear.
4. After the belt (E) Fig. 28 has been repositioned or
replaced on the pulleys, apply downward pressure on the
motor and tighten the two hex head bolts (D) (loosened in
STEP 3).
5. Use light finger pressure on the belt (E) Fig. 28 midway
between pulleys to check for proper tension. A deflection of
approximately 3/16" is correct.
6. Replace the hole plugs (B) Fig. 25.
Fig. 26
Fig. 27
Fig. 28
E
D
F
F
E
G
E
REMOVING AND REPLACING DRUM
SANDING BELT
The drum sanding belt is held on the drum with a spring
clip located on each side of the drum.
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Open drum cover (B) Fig. 31 to remove the sanding
belt (A) Fig. 29.
2. Press spring clips (C) Fig. 29 together and remove
one end of sanding belt (A). NOTE: Clip must be fully
depressed against the drum support.
3. Rotate the drum, (D) Fig. 31 by hand until you reach
the other end spring clip. Squeeze the spring clip to open
and remove the sanding belt (A).
4. To replace the sanding belt, press spring clip (C) Fig.
30 together and insert one end of sanding belt (A)
through the slot (S) in the drum and into the spring clip
(C). The taper cut end of the sanding belt must line up
with the edge of the drum.
5. Tightly wrap sanding belt (A) Fig. 31 around the drum
cylinder (D), keeping each wrap close to the previous
edge.
IMPORTANT: DO NOT OVERLAP THE EDGES OF
THE
SANDING BELT
(A)
. Insert the other end of the
sanding belt into the left spring clip (C) Fig. 29 as tightly as
possible.
6. The sanding belt will stretch during use. Periodically,
press spring clip (C) Fig. 29 and reinsert stretched length
into the clip.
Fig. 29
C
A
Fig. 30
A
Fig. 31
D
D
A
D
S
C
D
B
13