Delta (Model 31-300) Instruction Manual

Download Instruction manual of Delta (Model 31-300) Sander for Free or View it Online on All-Guides.com.

Brand: Delta

Category: Sander

Type: Instruction manual for Delta (Model 31-300)

Pages: 24 (2.08 Mb)

Download Delta (Model 31-300) Instruction manual

Delta (Model 31-300) Instruction manual - Page 1
1
Delta (Model 31-300) Instruction manual - Page 2
2
Delta (Model 31-300) Instruction manual - Page 3
3
Delta (Model 31-300) Instruction manual - Page 4
4
Delta (Model 31-300) Instruction manual - Page 5
5
Delta (Model 31-300) Instruction manual - Page 6
6
Delta (Model 31-300) Instruction manual - Page 7
7
Delta (Model 31-300) Instruction manual - Page 8
8
Delta (Model 31-300) Instruction manual - Page 9
9
Delta (Model 31-300) Instruction manual - Page 10
10
Delta (Model 31-300) Instruction manual - Page 11
11
Delta (Model 31-300) Instruction manual - Page 12
12
Delta (Model 31-300) Instruction manual - Page 13
13
Delta (Model 31-300) Instruction manual - Page 14
14
Delta (Model 31-300) Instruction manual - Page 15
15
Delta (Model 31-300) Instruction manual - Page 16
16
Delta (Model 31-300) Instruction manual - Page 17
17
Delta (Model 31-300) Instruction manual - Page 18
18
Delta (Model 31-300) Instruction manual - Page 19
19
Delta (Model 31-300) Instruction manual - Page 20
20
Delta (Model 31-300) Instruction manual - Page 21
21
Delta (Model 31-300) Instruction manual - Page 22
22
Delta (Model 31-300) Instruction manual - Page 23
23
Delta (Model 31-300) Instruction manual - Page 24
24
7
3. 240 VOLT SINGLE PHASE OPERATION
The motor supplied with your saw is a dual voltage,
120/240 volt motor. It is set at the factory at 120 volts. If
it is desired to operate your machine at 240 volts, single
phase, it is necessary to reconnect the motor leads in
the motor junction box by following instructions given on
the motor nameplate.
MAKE SURE MOTOR IS
DISCONNECTED FROM POWER SOURCE BEFORE
RECONNECTING MOTOR LEADS.
It is also necessary to replace the 120 volt plug, supplied
with the motor, with a UL/CSA listed plug suitable for
240 volts and the rated current of your machine as
illustrated in Fig. C. Contact your local Authorized Delta
Service Center or qualified electrician for proper
procedures to install the plug. The machine must comply
with all local and national electrical codes after the 240
volt plug is installed.
The machine with a 240 volt plug should only be
connected to an outlet having the same configuration as
the plug illustrated in Fig. C. No adapter is available or
should be used with the 240 Volt plug.
IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF
YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN
CHECK THE RECEPTACLE.
4. Permanently connected machines:
If the machine is intended to be permanently connected,
the machine should be connected to a grounded metal
permanent wiring system, or to a system having an
equipment-grounding conductor.
Fig. C
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows
the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Fig. D-1
Fig. D-2
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 120
up to
25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120
up to
25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120
up to
25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120
up to
25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
GREATER THAN 50 FEET NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 240
up to
50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG
6-10 240
up to
50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG
10-12 240
up to
50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG
12-16 240
up to
50 14 AWG
12-16 240 50-100 12 AWG
12-16 240
GREATER THAN 100 FEET NOT RECOMMENDED