Delta (Model 31-300) Instruction Manual

Download Instruction manual of Delta (Model 31-300) Sander for Free or View it Online on All-Guides.com.

Brand: Delta

Category: Sander

Type: Instruction manual for Delta (Model 31-300)

Pages: 24 (2.08 Mb)

Download Delta (Model 31-300) Instruction manual

Delta (Model 31-300) Instruction manual - Page 1
1
Delta (Model 31-300) Instruction manual - Page 2
2
Delta (Model 31-300) Instruction manual - Page 3
3
Delta (Model 31-300) Instruction manual - Page 4
4
Delta (Model 31-300) Instruction manual - Page 5
5
Delta (Model 31-300) Instruction manual - Page 6
6
Delta (Model 31-300) Instruction manual - Page 7
7
Delta (Model 31-300) Instruction manual - Page 8
8
Delta (Model 31-300) Instruction manual - Page 9
9
Delta (Model 31-300) Instruction manual - Page 10
10
Delta (Model 31-300) Instruction manual - Page 11
11
Delta (Model 31-300) Instruction manual - Page 12
12
Delta (Model 31-300) Instruction manual - Page 13
13
Delta (Model 31-300) Instruction manual - Page 14
14
Delta (Model 31-300) Instruction manual - Page 15
15
Delta (Model 31-300) Instruction manual - Page 16
16
Delta (Model 31-300) Instruction manual - Page 17
17
Delta (Model 31-300) Instruction manual - Page 18
18
Delta (Model 31-300) Instruction manual - Page 19
19
Delta (Model 31-300) Instruction manual - Page 20
20
Delta (Model 31-300) Instruction manual - Page 21
21
Delta (Model 31-300) Instruction manual - Page 22
22
Delta (Model 31-300) Instruction manual - Page 23
23
Delta (Model 31-300) Instruction manual - Page 24
24
1616
DISCONNECT MACHINE FROM POWER SOURCE
Fig. 33
Fig. 32
ADJUSTING SANDING DISC TABLE 90 DEGREES TO DISC
TILTING THE DISC SANDER TABLE
DISCONNECT MACHINE FROM POWER
SOURCE.
The table (A) can be tilted 45 degrees down (Fig. 34), by
loosening the lock handle (B), tilting the table (A), and
tightening lock handle (B). The degree of tilt is determined by
the scale and pointer.
Fig. 34
1. Loosen the disc table lock handle (A) Fig. 32, and move the table (B) Fig. 33 until the it contacts the stop. Tighten
the lock handle (A) Fig. 32.
2. Place a square (E) Fig. 33 on the table and against the sanding disc. See if the table is 90 degrees to the disc.
3. To adjust, loosen the lock handle (A) Fig. 32, and tighten or loosen the screw (F) Fig. 32 until the table is 90 degrees
to the disc.
4. The stop (F) Fig. 32 ensures that the table can rapidly return 90 degrees to the disc after the table has been
tilted.
5. Adjust pointer, if necessary.
ADJUSTING DISC TABLE MITER GAUGE SLOT PARALLEL TO SANDING DISC
DISCONNECT MACHINE FROM POWER
SOURCE
1. With the table (A) Fig. 35 positioned 90 degrees to the
disc, place a square (B) in the miter gauge slot with the
blade of the square touching the sanding disc.
2. Use a pencil to mark the disc where the blade contacts it.
(Fig. 35).
3. Rotate the disc to the other end of the table. Use a square
to check the distance between the miter gauge slot and
the mark on the disc made in STEP 3.
Fig. 35
A
BE
F
A
B
A
B