Kenwood KCA-RC35MR Instruction Manual
Download Instruction manual of Kenwood KCA-RC35MR Remote Control for Free or View it Online on All-Guides.com.
1
2
FCC
WARNING:
This equipment may generate
or
use radio frequency energy. Changes
or
modifications to this equipment may cause harmful interference
unless the modifications
are
expressly approved in
the
instruction
manual.
The
user
could lose
the authority to operate
this
equipment
if
an
unauthorized change
or
modification
is
made.
NOTE:
This equipment has been tested and found to comply with the limits
for a
Class
B digital device, pursuant
to
Part 15 of the
FCC
Rules. These
limits are designed to provide reasonable protection against harmful
interference
in
a residential installation. This equipment may cause
harmful
interference to radio communications, if
it
is
not
installed
and
used
in
accordance with
the
instructions. However, there
is
no
guarantee
that interference
will
not
occur in a particular installation.
If
this equipment does cause
harmful
interference to radio
or
television
reception, which can
be
determined
by
turning the equipment off and.on,
the
user
is
encouraged
to
try to correct the interference
by
one or more
of
the following
measures:
-- Reorient
or
relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Consult
the
dealer
or
an experienced radio technician for
help.
THIS DEVICE COMPLIES WITH
PART 15
OF
THE
FCC RULES.
OPERATION IS SUBJECT
TO
THE
FOLLOWING
TWO
CONDITIONS:
(1
)THIS DEVICE
MAY
NOT CAUSE
HARMFUL INTERFERENCE, AND
(2)THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE
THAT
MAY CAUSE UNDESIRED
OPERATION.
NOTICE:
This
Class
B
digital
apparatus complies with Canadian
ICES-003.
REMARQUE:
Cet
appareil
numeique
de
Ia
classe B est conforme
a
Ia
norma
NMB-003
du
Canada.
•English
Function and Operation
8
3
7
1.
Source Select
2.
Seek+
3.
Seek-
4.
Up (FM)
Before Installation
A
WARNING
If
you connect the ignition wire (re
d)
and
the
illumination
wire (orange)
to
the
negative ground point, you may
ca
use a
short circuit, that in turn may start a fire.
Always
connect those wires to the power
source running through
the
fuse box.
&
•
This unit is designed for marine use.
•
Mounting and wiring this product
requires
skill
and experience.
For
safe
ty
reasons
lea
ve
the mounting and wiring
work to professionals.
•
Make sure to ground the unit to a
negative
12V DC power
supply.
•
Do not
install
the unit
in
a spot exposed
to direct
sunlight
or
excessive heat and/
or
humidity.
•
Do
not
use your own screws. Use only
screws provided.
If
you use
the
wrong
screws you
could
damage the unit.
4
6
2
1
5
5. Down (AM)
6.
Volume
Up
7.
Volume
Down
8. Mute
I
Pause
• If
your
vessel
ignition does not have an
ACC
protection, connect the ignition wire
to a
power
source that can
be
turned on
and
off with the key or other control
switch.
If
the receiver is
left
on
for an
extended period
of
time the battery may
die.
• If
the
fuse blows, first make sure the
wires aren't touching to cause a short
circuit. Then
replace
the
old
fuse with one
of
the same rating.
• Insulate
unconnected wires with
vinyl
tape
or
other
similar material.
To
prevent
a short circuit
do
not
remove
the
caps on
the ends of the unconnected wires
or
the
terminals.
•
After
installing
the unit, check to make
sure that
electrical
equipment such
as
the
signal lamps and gauges operate
normally.
KENWOOD
KCA-RC35MR
REMOTE CONTROL UNIT
INSTRUCTION
MANUAL
UNITE DE
TELECOMMANDE
MODE D'EMPLOI
UNlOAD
DE
CONT-ROL REMOTO
MANUAL DE
INSTRUCCIONES
JVC KENWOOD
Corporation
US
Resident Only
Register
Online
Installation
1.
Set
the gasket to the
place
where the KCA-RC35MR is
to
be
installed
and pierce with a
drill
bit for wiring harness and the installation.
2. Fix the KCA-RC35MR
as
shown
in
figure.
Connection
KCA-RC35MR
Remote
Control Input
CD
- Receiver
Ground Wire
(Black)
To
a negative ground point of the
vessel
Fuse box
(Main Fuse)