Honeywell Notifier 002-467 Manual
Download Manual of Honeywell Notifier 002-467 Gateway for Free or View it Online on All-Guides.com.
1
2
3
4
5
6
7
8
9
997-451, Issue 6 July 2006
1
Installing the Network Gateway Unit (NGU)Installing the Network Gateway Unit (NGU)
The Network Gateway Unit (PN: 002-467) consists of a Back Box (with cover) with the following fitted on a chassis: a PSU3A
to Network Interface PCB and a Network Gateway Module (NGM) PCB. There is space for a PSU3A and two 12Ah batteries.
2
This basic configuration is used as an ID net Network Booster. The chassis allows a Fibre-optic PCB and RS232 PCB (for
connection of a network repeater) to be fitted.
The PSU3A provides a 28V output and a battery charger. The PSU3A to Network Interface PCB provides battery and PSU
fault monitoring, controls the battery charger and converts 28V dc to 5V dc (for the Network PCB). Alternatively, the NGU can
be powered by an external 28V supply connected at the PSU3A to Network Interface PCB.
The Network Gateway Unit (PN: 002-467) consists of a Back Box (with cover) with the following fitted on a chassis: a PSU3A
to Network Interface PCB and a Network Gateway Module (NGM) PCB. There is space for a PSU3A and two 12Ah batteries.
This basic configuration is used as an ID net Network Booster. The chassis allows a Fibre-optic PCB and RS232 PCB (for
connection of a network repeater) to be fitted.
The PSU3A provides a 28V output and a battery charger. The PSU3A to Network Interface PCB provides battery and PSU
fault monitoring, controls the battery charger and converts 28V dc to 5V dc (for the Network PCB). Alternatively, the NGU can
be powered by an external 28V supply connected at the PSU3A to Network Interface PCB.
2
Your Network Gateway Unit, PN: 002-467 should contain:
Back box, NGU, with electronics and cover.
Anti-static Warning Instructions PN: 997-180
Accessory kit, NGU PN: 020-685
The Accessory kit should contain:
Battery interlink assembly PN: 082-082-002
Screw M3 x 6mm button head (8 off) PN: 775-059
Hex key 2mm PN: 334-051
Fuse T 2A H 250V (2 off) PN: 570-106
Fuse T 500mA 250V PN: 570-105
Ferrite (5 off) PN: 670-068
Cable tie (1 off) PN: 233-144
NGU EN54-compliant label PN: 345-497 or
PN: 345-499
Cable Assembly (PSU3A dc power) PN: 082-244
Cable Assembly (short: NGM/RS232) PN: 082-177-001
Cable Assembly (x-over: NGM/repeater) PN: 082-255
Your Network Gateway Unit, PN: 002-467 should contain:
Back box, NGU, with electronics and cover.
Anti-static Warning Instructions PN: 997-180
Accessory kit, NGU PN: 020-685
The Accessory kit should contain:
Battery interlink assembly PN: 082-082-002
Screw M3 x 6mm button head (8 off) PN: 775-059
Hex key 2mm PN: 334-051
Fuse T 2A H 250V (2 off) PN: 570-106
Fuse T 500mA 250V PN: 570-105
Ferrite (5 off) PN: 670-068
Cable tie (1 off) PN: 233-144
NGU EN54-compliant label PN: 345-497 or
PN: 345-499
Cable Assembly (PSU3A dc power) PN: 082-244
Cable Assembly (short: NGM/RS232) PN: 082-177-001
Cable Assembly (x-over: NGM/repeater) PN: 082-255
Check your equipment....Check your equipment....
Take suitable anti-static precautions, such as wearing a grounded
wrist strap, when following ALL instructions. Remove all packaging
from the kit and ensure that it has not been damaged in transit (and
that no items are missing - see checklist on the left) before proceeding
any further. If no damage is evident, proceed using the instructions
below. In the unlikely event that damage has occurred or items are
missing, DO NOT PROCEED, contact your supplier and refer to the
panel’s Installation & Commissioning Manual.
To install the Network Gateway Unit it is necessary to remove the
supplied electronics chassis (to prevent damage), fit the back box to
the wall, re-install the supplied electronics chassis, and fit any
required options. Instructions are given on the following pages.
Take suitable anti-static precautions, such as wearing a grounded
wrist strap, when following ALL instructions. Remove all packaging
from the kit and ensure that it has not been damaged in transit (and
that no items are missing - see checklist on the left) before proceeding
any further. If no damage is evident, proceed using the instructions
below. In the unlikely event that damage has occurred or items are
missing, DO NOT PROCEED, contact your supplier and refer to the
panel’s .
To install the Network Gateway Unit it is necessary to remove the
supplied electronics chassis (to prevent damage), fit the back box to
the wall, re-install the supplied electronics chassis, and fit any
required options. Instructions are given on the following pages.
Installation & Commissioning Manual
MAINS
TERMINATION
BLOCK
MAINS
TERMINATION
BLOCK
BACK
BOX
BACK
BOX
FIBRE-OPTIC
PCB
(OPTIONAL)
FIBRE-OPTIC
PCB
(OPTIONAL)
NETWORK
PCB (NGM)
NETWORK
PCB (NGM)
PSU3A TO
NETWORK
INTERFACE
PCB
PSU3A TO
NETWORK
INTERFACE
PCB
BATTERIES
(NOT SUPPLIED)
BATTERIES
(NOT SUPPLIED)
CHASSISCHASSIS
PSU3A
(OPTIONAL)
PSU3A
(OPTIONAL)
EARTH
TERMINATION
KIT (OPTIONAL)
EARTH
TERMINATION
KIT (OPTIONAL)
ISOLATED
RS232 PCB
(OPTIONAL)
ISOLATED
RS232 PCB
(OPTIONAL)
OBSERVE PRECAUTIONS FOR HANDLING
ELECTROSTATIC SENSITIVE DEVICES
OBSERVE PRECAUTIONS FOR HANDLING
ELECTROSTATIC SENSITIVE DEVICES
ATTENTIONATTENTION
MAINS
TERMINAL
BLOCK
L, N, E
L, N
PSU
3A
SAFETY
EARTH TO
BACK BOX
EARTH TO
PSU
PCB -
PSU3A
TO
NETWORK
INTERFACE
RIBBON
28V DC
PCB -
NETWORK
(NGM)
PCB -
FIBRE-
OPTIC
(OPTION)
RIBBON
5V DC
CH1 CH2
2
ID NET
CH1
RX/TX
CH2
RX/TX
2
ID NET
BATTERIES
EARTH TO
UNIT COVER,
& EARTH TO
CHASSIS
PSU
FAULT
28V DC
FROM
EXTERNAL
SOURCE
(OPTION)
(OPTION)
(OPTION)
REPEATER
RS232
28V
PCB -
ISOLATED
RS232
(OPTION)
Note:
See Section ‘PSU3A to Network
Interface PCB - if using PSU3A’
for 28V supplies to external
equipment.
CROSS-
OVER
RIBBON
(OPTION)
by Honeywell