GE Current Lumination IS Series Installation Manual
Download Installation manual of GE Current Lumination IS Series Lantern for Free or View it Online on All-Guides.com. This version of GE Current Lumination IS Series Manual compatible with such list of devices, as: Current Lumination IS Series, Current Lumination ISC Series, Current Lumination ISI Series, Current Lumination ISS Series
Brand: GE
Category: Lantern
Type: Installation manual
Model: GE Current Lumination IS Series , GE Current Lumination ISC Series , GE Current Lumination ISI Series , GE Current Lumination ISS Series
Pages: 45
Download GE Current Lumination IS Series Installation manual
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Installation Guide
Save These Instructions
Use only in the manner intended by the manufacturer. If
you have any questions, contact themanufacturer.
Tools and Components Required:
• T15 torx or phillips #2screwdriver
• UL Listed conduit connections per NEC/CEC
for nominal conduit trade sizes ½” or ¾”
• UL Listed wire connectors
Components Supplied:
• Luminaire
• 2 MountingBrackets
• End Caps (2 supplied with IS1 series and ISS series)
Note: In general case, with the Starter Kit, the Starter SKU
will not be required.
Table of Contents Page
Accessory Kits
2
Installation of an Independent Unit (IS1) 3
Installation of a Continuous Row using a Starter Kit 4
Installation of a Continuous Row with Optional
BranchCircuit
6
PSU Replacement 10
Light Engine Replacement 11
Prepare Electrical Wiring
Electrical Requirements
The LED fixture must be supplied with 120-277VAC,
50/60Hz or 347V, 50/60Hz and protected by a max.
20 ampere circuit breaker. Use min. 75°C supply
conductor. 347V power should only be supplied to
luminaires with voltage code “D”.
Grounding Instructions
The grounding and bonding of the overall system
shall be done in accordance with National Electric
Code (NEC) Article 600 and local codes.
RISK OF ELECTRICSHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electricalenclosure.
RISK OF ELECTRICSHOCK
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG or 14 AWG for continuous runs.
• When using multi-branch wire circuits with a shared neutral, do not
are secure before energizingthe circuit. An open neutral can cause an
overvoltage condition at the luminaire power supply.
RISQUES DE DÉCHARGESÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier
d’alimentation électrique.
RISQUESD’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des fils approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG ou 14 AWG pour les rangées continues.
operate any circuit with the neutral open. Also ensure all neutral connections
• Lorsque vous utilisez des circuits câblés à branches multiples avec un
neutre commun, ne mettez aucun circuit en service avec le neutre ouvert.
Assurez-vous également que tous les raccords neutres soit sécurisés avant
de mettre le circuit sous tension. Un neutre ouvert peut causer une condition
de surtensionà l’alimentationdu luminaire.
Lumination
TM
LED Luminaire
(IS Series)
There are three types of fixtures:
• S
tarter (ISSseries)
• Continuous (ISC series)
• Independent (IS1series)
Use Starter Kit in general case. Use Starter SKU if preferred.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Important notes included below and on page 3.
WARNING/AVERTISSEMENT
1