CRAFTSMAN Security+ EntryEase 139.53555 User Manual

Download Operation & user’s manual of Craftsman Security+ EntryEase 139.53555 Remote Control for Free or View it Online on All-Guides.com.

Craftsman Security+ EntryEase 139.53555 Operation & user’s manual - Page 1
1
Craftsman Security+ EntryEase 139.53555 Operation & user’s manual - Page 2
2
Incorrect
Do not bend finger during the swipe
as this will only scan the tip of your
finger.
Swipe straight down, not at an angle.
Swipe flat, not tilted or rolled to one
side.
1
Model 139.53555 Security
®
EntryEase
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
®
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• Install Keyless Entry Control within sight of the garage door, out of
reach of children at a minimum height of 5 feet (1.5 m), and away
from all moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
OVERVIEW
For use with any 315 MHz SECURITY
®
garage door openers
having a purple “learn” button.
The EntryEase system uses biometric technology that enables
an authorized user to gain access by scanning their fingerprint.
The sensor strip on the unit makes a numeric template of the
fingerprint that is unique only to that user.
Resend Button: When pressed the traveling door will reverse.
The fingerprint sensor is inactive for
15 seconds after valid swipe so
reswiping will not reverse the door.
Enroll Button: When pressed the
Enroll LED will light up signaling
that the device is in enroll mode.
READY LED: Lit (green) when unit
is ready to accept a fingerprint scan.
PASS LED: Lit (green) when a
scanned fingerprint matches a
stored print.
FAIL LED: Lit (red) when a scanned
fingerprint does not match a stored
print.
RETRY LED: Lit (yellow) when another swipe is required.
ENROLL LED: Lit (yellow) when the unit is in enroll mode.
SEND LED: Lit (yellow) after a passed fingerprint scan and
enables the Resend button for retransmission.
NOTE: The term “enroll” refers to scanning the fingerprint so
the device will recognize the user. The term “swipe” refers to
the movement of the finger across the sensor strip. The term
“LED” stands for Light Emitting Diode.
INSTALLATION
1. Choose a convenient
location for installation.
Install out of the reach of
children at a minimum
height of 5 feet (1.5 m),
away from all moving parts
of door.
For a one-piece door,
choose the optional
location shown in the
illustration to avoid injury as
the door swings up and out.
2. Remove the cover to access the top
mounting hole by sliding past the “up stop”
position.
3. Center the unit at eye level against the
selected location. Mark the bottom edge at
the center of the unit and remove from wall.
Measure up 1-1/4" (3.2 cm) from this mark
to locate the bottom mounting hole. Be sure
that you have at least 11" (28 cm)above this
mark to allow for the removal of cover. Drill
a 1/8" (3.2 mm) pilot hole. Install bottom
mounting screw, allowing 1/8"
(3.2 mm) to protrude above surface.
Position unit on screw head and adjust for
snug fit.
With cover off so top mounting hole is visible, mark the
position of the hole. Remove unit and drill 1/8" (3.2 mm) pilot
hole. Replace unit and complete installation of top screw,
using care to avoid cracking plastic housing. Do not over
tighten. To replace cover, insert into tracks and slide down.
Door Jamb Edge
(Optional)
Keyless
Entry
Door Jamb Face
(SECTIONAL DOOR ONLY)
KEYLESS ENTRY MUST BE
INSTALLED WITHIN
SIGHT OF THE DOOR
Exterior Front Wall
1-Piece or
Sectional Door
Typical
Installation
Send LED
Pass LED
Ready LED
Enroll button
Enroll LED
Fail LED
Retry LED
Unit Cover
Sensor Strip
Resend button
TIPS FOR SUCCESSFUL ENROLLMENT
Correct
1. Make sure finger is free of grease or
dirt. Place finger flat above the
sensor strip with the top knuckle
above the sensor.
2. Swipe finger straight down keeping
firm contact with the sensor. The
swipe should be a slow, constant
speed.
NOTE: Use the same finger for every
swipe.
UNIT MUST BE INSTALLED
WITHIN SIGHT OF THE DOOR
EntryEase
1-1/4"
(3.2 cm)
Back View