• Home
• Brands
• Aotec Manuals
• Aotec Smart Switch 6
• Aotec ZW096 User Manual

Aotec ZW096 User Manual

Download Operation & user’s manual of Aotec Smart Switch 6 Switch for Free or View it Online on All-Guides.com.

1

2

View the expanded manual:

http://aeotec.com/support

Smart Switch 6

Aeotec by Aeon Labs Smart Switch.

Aeotec Smart Switch is a low-cost Z-Wave Switch plug-

in module specically used to enable Z-Wave command

and control (on/off) of any plug-in tool. It can report

immediate wattage consumption or kWh energy usage

over a period of time. In the event of power failure, non-

volatile memory retains all programmed information

relating to the unit’s operating status.

Its surface has a Smart RGB LED, which can be used

for indicating the output load status or strength of the

wireless signal. You can congure its indication colour

according to your favour.

The Smart Switch 6 is also a security Z-wave device and

supports Over The Air (OTA) feature for the products

rmware upgrade.

®

Familiarize yourself with your Smart Switch.

Getting your Smart Switch up and running is as simple

as plugging it into a wall socket and adding it to your

Z-Wave network. The following instructions tell you how

to add your Smart Switch to your Z-Wave network via

Aeotec by Aeon Labs’ Z-Stick or Minimote controller.

If you are using other products as your main Z-Wave

controller, such as a Z-Wave gateway, please refer to

the part of their respective manual that tells you how to

add new devices to your network.

(Note: this gure is a sample of USA version. For other

versions, the product appearance would be different).

If you’re using a Z-Stick:

Quick start.

3.

4.

5.

6.

7.

1.

2.

Decide on where you want your Smart Switch to be

placed and plug it into a wall outlet.

If your Z-Stick is plugged into a gateway or a

computer, unplug it.

If you’re using a Minimote:

1.

2.

3.

4.

5.

Decide on where you want your Smart Switch to be

placed and plug it into a wall socket.

Take your Minimote to your Smart Switch.

Press the Include button on your Minimote.

Press the Action Button on your Smart Switch.

If Smart Switch has been successfully added to your

Z-Wave network, its RGB LED will be solid. If the

adding was unsuccessful, the red LED will be on for

2 seconds and then remain colourful gradient status,

repeat the instructions from step 4.

Press any button on your Minimote to take it out of

inclusion mode.

With your Smart Switch now working as a part of your

smart home, you’ll be able to configure it from your

home control software. Please refer to your software’s

user guide for precise instructions on conguring Smart

Switch to your needs.

The colour of RGB LED will change according to the

output load power level when it is in Energy mode:

Version LED indication Output (W)

US

Green [0W, 900W)

Yellow [900W, 1600W)

Red [1600W, 2000W)

AU

Green [0W, 1000W)

Yellow [1000W, 2000W)

Red [2000W, 2500W)

EU

Green [0W, 1500W)

Yellow [1500W, 2500W)

Red [2500W, 3000W)

You can also configure the brightness of RGB LED

when the Smart Switch is in Energy mode, Momentary

Indicate mode, or Night Light mode.

Your Smart Switch can be removed from your Z-Wave

network at any time. You’ll need to use your Z-Wave

network’s main controller to do this and the following

instructions will tell you how to do this using a Aeotec

by Aeon Labs’ Z-Stick or Minimote controller. If you are

using other products as your main Z-Wave controller,

please refer to the part of their respective manuals that

tells you how to remove devices from your network.

Removing your Smart Switch from a Z-Wave

network.

If you’re using a Z-Stick:

1.

2.

3.

4.

5.

If your Z-Stick is plugged into a gateway or a

computer, unplug it.

Take your Z-Stick to your Smart Switch.

Press the Action Button on your Z-Stick.

Press the Action Button on your Smart Switch.

If your Smart Switch has been successfully removed

from your network, its RGB LED will remain colourful

gradient status. If the removal was unsuccessful, the

RGB LED will still be solid (Energy mode state when

the output is on or Night light mode state when the

output load is off), repeat the instructions from step 3.

If you’re using a Minimote:

1.

2.

3.

4.

5.

Take your Minimote to your Smart Switch.

Press the Remove Button on your Minimote.

Press the Action Button on your Smart Switch.

If your Smart Switch has been successfully removed

from your network, its RGB LED will remain

the colourful gradient status. If the removal was

unsuccessful, the RGB LED will still be solid (Energy

mode state when the output is on or Night light

mode state when the output load is off), repeat the

instructions from step 2.

Press any button on your Minimote to take it out of

removal mode.

Take your Z-Stick to your Smart Switch.

Press the Action Button on your Z-Stick.

Press the Action Button on your Smart Switch

If Smart Switch has been successfully added to your

Z-Wave network, its RGB LED will be solid. If the

adding was unsuccessful, the red LED will be on for

2 seconds and then remain colourful gradient status,

repeat the instructions from step 4.

Press the Action Button on the Z-Stick to take it out of

inclusion mode and then return it to your gateway or

computer.

6.

Changing LED mode.

You can change the mode of how the LED acts through

Advanced functions.

6. Press the Action Button on the Z-Stick to take it out of

removal mode.

Security or Non-security feature of your Smart

Switch in Z-wave network.

Including Smart Switch as a non-secure device:

If you want your Smart Switch is a non-security device

in your Z-wave network, you need to press the Action

Button once on Smart Switch when you use a controller/

gateway to add/include your Smart Switch. If the

inclusion is successful, the green LED will be on for 2

configuring the Smart Switch. There are 3 different

modes: Energy mode, Momentary indicate mode, and

Night light mode.

Energy mode will allow the LED to follow the state of the

Smart Switch, when the switch is on, the LED will be on,

and while the switch is off, the current colour LED will be

off and then remain the purple colour of 10% brightness.

Momentary indicate mode will momentarily turn the LED

on for 5 seconds then turn off after every state change

in the switch. Night light mode will allow the LED to be

turned on and off during your selected time of day you

have congured for it.

Parameter 81 [1 byte dec] can be set to:

(0) Energy Mode

(1) Momentary Indicate Mode

(2) Night Light Mode