Bosch TDA4625GB Operating Instructions

Download Operating instructions of Bosch sensixx B3 Iron, Steam Cleaner for Free or View it Online on All-Guides.com. This version of Bosch sensixx B3 Manual compatible with such list of devices, as: sensixx B3, TDA46 Series, TDA4622GB, TDA4625GB, TDA4632GB

Bosch sensixx B3 Operating instructions - Page 1
1
Bosch sensixx B3 Operating instructions - Page 2
2
DO NOT de-scale or clean the water tank with cleaning products
or solvents, as these could cause the iron to drip when using the
steam function.
DO NOT use a “professional steam cleaner” for cleaning the
appliance.
DO NOT use sharp objects or abrasive products to clean the
soleplate or any other part of the appliance. To keep the soleplate
in good condition, do not allow it to come into contact with metal
objects.
GUARANTEE TERMS
The terms of the guarantee for this appliance are in accordance
with that stated by our representative for the country in which
it is sold. Details of those conditions can be obtained from the
retailer from whom the appliance was purchased. The SALES
RECEIPT must be presented when making any claims against the
terms of this guarantee. We reserve the right to make technical
modifications.
Environmental Care
This iron has been designed according to ecological criteria,
related to the sustainable development, analyzing its whole
lifecycle - from material selection to its later reusing or recycling
- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.
Before throwing a used appliance away, you should make it
noticeably inoperable e.g. cut off the mains lead and be certain to
dispose of it in accordance with current laws and regulations.
Your retailer, town council or local council can give you detailed
information about these.
This appliance is labelled in accordance with
European Directive 2002/96/EG concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The guideline determines the framework for the return
and recycling of used appliances as applicable throughout
the EU.
Important
This appliance has been designed exclusively for domestic use
and must not be used for industrial purposes.
Carefully read through the operating instructions for the appliance
and safeguard them for future reference.
003 TDA46..GB/03/10
Operating instructions
Solving Minor Problems Yourself
Problem Possible Causes Solution
Iron does not
work or is not
heating up
Temperature control (J)
set to minimum
Turn the temperature
control to the desired
position
Connection problems Check that the plug is
inserted into the mains
socket correctly
The automatic shut-
off system has been
activated (*)
Move the iron gently
from side to side to
re-start it
Iron is not
steaming
There is no water in the
tank (I)
Fill the water tank
The steam regulator (A)
is in the position
Set the steam regulator
to the relevant position
Water is
dripping from
the holes in
the soleplate
The temperature
control (J) is set too
low for the iron to
produce steam.
Set the temperature
control within the
steam area (between
the “••” and “max”) or
turn the steam regulator
(A) to
You have pressed the
shot of steam button
(C) repeatedly without
waiting for 5 seconds
between each press
Wait 5 seconds
between each press of
the jet of steam button
Water has been left
in the tank (I) when
the soleplate was
cold, with the steam
regulator (A) set at
position different to
Always empty the tank
after ironing and set the
steam regulator to
after ironing and when
filling the tank
Water is
dripping from
the holes in
the soleplate
Tap or part distilled
water has not been
used (see “Filling the
water tank” section) or
other products such
as fragrant water have
been added to the tank
Mix distilled water with
tap water as directed
in the “Filling the water
tank” section and never
add any other products
to the water tank
Deposits
come out
through the
holes in the
soleplate
Traces of lime scale
are coming out of the
steam chamber
Carry out a cleaning
cycle (see “Multiple
de-scaling system”
section)
Flashing lamp
on top of
handle (*)
Auto-shut off has been
activated.
Move the iron gently
fromside to side to
re-start it. The lamp will
then flash once before
it re-heats
Thank you for buying the TDA46 steam iron from Bosch. This iron
has a lightweight design and is built to perform.
These instructions contain valuable information about the unique
features of this iron and some hints to make ironing easier for
you.
Please visit www.bosch-home.co.uk for more product
information or to register your product, just follow the link
to the Online guarantee registration.
Before using the iron for the first time
Please carry out the following steps:
1. Remove the protective cover from the soleplate before using
the iron.
2. While the iron is unplugged, fill the water tank (I) with tap
water
3. Plug the appliance into the mains and set the temperature
control (J) to the maximum position by lining it up with the
pointer (H) on the iron.
4. When the iron has reached the correct temperature, the pilot
lamp (L) goes out. Set the steam regulator (A) to the maximum
position.
5. Hold the iron horizontally and repeatedly press the shot of steam
button (C). Any dirt should come out of the soleplate (F). It may
smoke and smell this is normal and will cease after a short
while.
6. If necessary, carefully clean the soleplate down with a dry, folded
cloth
Cleaning and Maintenance
Attention ! Risk of burns !
For general cleaning, follow the information below:
Problem Solution
Dirty/lightly marked
iron body or
soleplate
Clean body of iron or soleplate with a
damp cloth then dry it.
Mark develops on
soleplate during use
Set the iron to its maximum
temperature setting. Rub the iron a
few times over with a dry cotton cloth
folded several times.
Heavily stained
soleplate
While the iron is cold, iron a linen cloth
soaked in white vinegar. Then dampen
a cloth with water and wipe the
soleplate clean and dry thoroughly.
TDA46..
sensixx B3
(*) Model dependent
You can download this manual from the local homepages of Bosch
Customer Service
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT
UK +44 (0)844 892 8923
IRL +353 (0)1450 2655
www.bosch-home.co.uk
General safety warnings
• Danger of electric shocks or fire!
This appliance is to be connected and used in accordance with
the information stated on its characteristics plate.
This appliance must be connected to an earthed socket. If
it is absolutely necessary to use an extension cable, make
sure that it is suitable for 16A and has a socket with an earth
connection.
The iron should not be used if it has been dropped, if there
are visible signs of damage or if it is leaking water. It must be
checked by an authorized Technical Service Centre before it
can be used again.
Do not allow the power cable to come into contact with the
soleplate when it is hot.
In order to avoid that, under unfavourable mains conditions,
phenomena like transient voltage drops or lighting fluctuations
can happen, it is recommended that the iron is connected to a
power supply system with a maximum impedance of 0.27Ω . If
necessary, the user can ask the public power supply company
for the system impedance at the interface point.
This appliance is not intended to be used by persons (including
children) with reduced physical, sensory or mental capacities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
Keep the appliance out of children’s reach.
Children should be supervised to ensure that they do not play
with the appliance.
Remove the plug from the socket before filling the appliance with
water or before pouring out the remaining water after use.
The appliance must never be placed under the tap to fill the
water tank.
The appliance must be used and placed on a stable surface.
When placed on its stand, make sure that the surface on which
the stand is placed is stable.
The iron must not be left unattended while it is connected to
the supply mains.
Unplug the appliance from the mains supply after each use, or
if a fault is suspected.
The electrical plug must not be removed from the socket by
pulling the cable.
Never immerse the iron in water or any other fluid.
Do not leave the appliance exposed to weather conditions (rain,
sun, frost, etc.)
With the aim of avoiding dangerous situations, any work or
repair that the appliance may need, e.g. replacing a faulty mains
cable, must only be carried out by qualified personnel from an
Authorised Technical Service Centre.