Bosch ISP-EM55FM-120 Quick Installation Manual

Download Quick installation manual of Bosch ISP-EM55FM-120 Extender for Free or View it Online on All-Guides.com.

Brand: Bosch

Category: Extender

Type: Quick installation manual for Bosch ISP-EM55FM-120

Pages: 2

Download Bosch ISP-EM55FM-120 Quick installation manual

Bosch ISP-EM55FM-120 Quick installation manual - Page 1
1
Bosch ISP-EM55FM-120 Quick installation manual - Page 2
2
Safety
!
Caution!
Electricity
Injuries due to electricity are possible.
Switch off all electricity while installing
the product.
Do not open or modify this product, ex-
cept if described in this manual.
Old electrical and electronic appliances
Electrical or electronic devices that are no
longer serviceable must be collected separately
and sent for environmentally compatible recyc-
ling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic
devices, you should use the return and collec-
tion systems put in place in the country con-
cerned.
Short information
This zone expander module integrates manual
conventional sensor technology (e.g. conven-
tional magnet contacts) into the local security
network (LSN).
System overview
1
2 3
4
5
6
Fig.1: System overview
Element Description
1 Recessed socket
2 Mount with PCB
3 Housing cover fastening screw
4 Adhesive seal
5 Housing cover
6 Fastening screws
Installation
Notice!
The recessed socket is not part of the
delivery. Use a recessed socket accord-
ing to DIN 49073 part I.
How to mount the zone expander module
1. Connect the PCB.
2. Place the mount with PCB into a re-
cessed socket and lock it in position us-
ing the two fastening screws.
3. Fit the housing cover on the mount with
PCB and secure it with the housing cover
fastening screw.
4. Put the adhesive seal onto the housing
cover fastening screw.
Connection
!
Caution!
Incorrect cabling
Incorrect cabling leads to malfunction
of the system.
!
Caution!
Cable length
Exceeding the permitted cable length is
not covered by CE declarations and
leads to malfunction of the system.
Do not exceed the total cable length of 500
m per loop for the primary cables, the con-
trol cables and the contact cables of EM 55,
KD55/1, NKK, NNK 100 2-wire, NVK and IC
400.
Permitted cable length of the primary cables
(PL)
Maximum length of unshielded cable: 3 m
Maximum length of shielded cable: 500 m
LSN connection
Voltage supply can be fed-through (other-
wise free terminals for 0V/+U).
Incoming and outgoing LSN can be swapped
over.
4-wire and 2-wire connections
Notice!
A mixed operation of a 4-wire connec-
tion at one of the primary outputs and
a 2-wire connection at the other
primary output is not permitted.
Notice!
For a 4-wire connection always use un-
shielded cables.
For a 2-wire connection always use
shielded cables.
4-wire connection (unshielded)
Use a 4-wire connection with an unshielded
cable with a maximum length of 3 m and the
internal EOL resistor (e.g. for magnetic con-
tacts).
With an unshielded cable, do not connect
contacts with metallic enclosure.
LSN
aLSN1
bLSN1
0V
+U
aLSN1
bLSN1
aLSN2
bLSN2
0V
I1
I2
I3
I4
II5
I6
II1
II2
II3
II4
II6
RE1
RE2
PL1
PL2
RE1
RE2
I5
I7
+U
aLSN2
bLSN2
0V
+U
II7
1
2
2
3
Element Description
1 Terminal for fed-through voltage sup-
ply
2 LSN connection
3 4-wire connections, e.g. magnet con-
tacts (unshielded)
2-wire connection (shielded)
Use a 2-wire connection with a shielded
cable with a maximum length of 500 m and
an external EOL resistor (e.g. for lock con-
tacts).
Connect shielding only to the zone expander
module.
Use one ferrite bead per shielding.
LSN
aLSN1
bLSN1
0V
+U
aLSN1
bLSN1
aLSN2
bLSN2
0V
I1
I2
I3
I4
II5
I6
II1
II2
II3
II4
II6
RE1
RE2
PL1
PL2
RE1
RE2
I5
I7
+U
aLSN2
bLSN2
0V
+U
II7
1
2
2
R
R
3
4
Element Description
1 Terminal for fed-through voltage sup-
ply
1 | 2 | 3 | 4 |
5 | 6 | 7 | 8 |