JBL GTO24001 Owner's Manual
Download Owner's manual of JBL GTO24001 Amplifier, Car Amplifier for Free or View it Online on All-Guides.com.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Installation Warnings and Tips
• Disconnect the negative (–) lead from your vehicle’s
battery.
• At the installation sites, locate and make a note of
all fuel lines, hydraulic brake lines, vacuum lines
and electrical wiring. Use extreme caution when
cutting or drilling in and around these areas.
• Choose a safe mounting location away from moisture.
• Make sure there is sufficient air circulation at the
mounting location for the amplifier to cool itself.
• Mount the amplifier, using the supplied hardware.
Specifications
• 1700W RMS x 1 channel @ 4 ohms and ≤1% THD + N*
• 2400W RMS x 1 channel @ 2 ohms, 14.4V supply and
<
1% THD + N*
• Frequency response: 20Hz – 330Hz (–3dB)
• Maximum input signal: 6V*
• Maximum sensitivity: 200mV*
• THD + N: 0.5%
• Signal-to-noise ratio: 65dBA
(reference 1W into 4 ohms)*
• Signal-to-noise ratio: 97dBA
(reference rated power into 4 ohms)
* CEA-2006A-compliant
0
Speaker Output Connectors
• Connect the speakers to these terminals,
observing proper polarity. Either + or –
terminal may be used. Minimum total
impedance is 2 ohms.
1
Fuse Holder/+12V Connection
• Replace fuse only with the same type and rating.
• Mount the fuse holder within 18" (45cm) of the
vehicle’s battery, inside the engine compart-
ment, and connect one end of the fuse holder
to the battery’s “+” terminal using a single piece
of 0-gauge (0 AWG, 53.5mm
2
) wire, as shown in
Figures 1 and 2.
• For normal installation, connect two pieces of
4-gauge (4 AWG, 22mm
2
) wire to the other end of
the fuse holder, as in Figure 1. Route both pieces
of 4-gauge (4 AWG, 22mm
2
) wire through the car,
using rubber grommets in all locations where
the wire must pass through metal. Connect the
other end of the 4-gauge (4 AWG, 22mm
2
) wire to
the two “+” terminals on the amplifier’s power
connectors
2
(refer to illustrations page).
Figure 1.
• For competition installations, replace the fuse
with a 300A ANL (not included). Connect a single
piece of 0-gauge (0 AWG, 53.5mm
2
) wire to the
other end of the fuse holder, as in Figure 2.
Route the 0-gauge (0 AWG, 53.5mm
2
) wire
through the car, using rubber grommets in all
locations where the wire must pass through
metal. Connect the other end of the 0-gauge
(0 AWG, 53.5mm
2
) wire to the input terminal of a
power distribution block (not included) designed
to accept 0-gauge (0 AWG, 53.5mm
2
) wire.
Connect two pieces of 4-gauge (4 AWG, 22mm
2
)
wire to the distribution block and connect the
other ends of the wire to the two “+” terminals
on the amplifier’s power connectors
2
(refer to
illustrations page).
Figure 2.
2
Power Input Connectors
• +12V: See ”Fuse Holder“
1
.
• GND: Connect to the vehicle’s chassis using
4-gauge (4 AWG, 22mm
2
) wire. Refer to Figure 3.
Figure 3.
• REM: Connect to the “Remote Out” lead from
the source unit or to a source of switched
12V+ (ACC).
3
Aux Output Connectors (RCA)
• Nonfiltered pass-through output. Connect to the
input of an additional amplifier.
4
Input Connectors (RCA)
• Connect to the RCA outputs from the source unit
or signal processor.
5
Input-Level Control
• Used to match the input level of the amplifier
to the output level of the source unit.
• See
B
for the adjustment procedure.
6
Low-Pass Filter Frequency Control
• 12dB/octave low-pass filter,
variable from 32Hz to 320Hz.
• See
C
for the adjustment procedure.
7
DBO (Dynamic Bass Optimization) Variable
Subsonic High-Pass Filter With Variable Boost (Q)
• For woofers in tuned (vented) enclosures, set
the Frequency control to a value 10Hz below the
enclosure’s resonance (tuned) frequency.
• For woofers in sealed boxes, set the control to
any value you prefer, between 30Hz and 50Hz.
• Set the Boost control according to your
preference, being careful not to apply
enough boost to damage your woofer(s).
A DBO High-Pass Filter Frequency control,
variable between 10Hz and 100Hz. See
above for appropriate settings.
B DBO Boost control provides up to
12dB of boost, slightly above the high-
pass filter’s frequency. See above for
appropriate settings.
8
Optional Remote Level Control (RLC) Connector
• Connect the Remote Level Control (RLC) here,
using the RJ-11 cable (Supplied with RLC).
9
Power On LED
• Illuminated when the amplifier is on.
A
Protect LED
• Illuminated under any of the following fault
conditions: battery over/under voltage, short
circuit in speaker wires, amplifier is too hot,
amplifier’s output circuit has failed (DC voltage
is present in the amplifier’s output).
B
Setting Input Level
A Turn Input Level control counterclockwise to
6V (minimim).
B With a dynamic music track playing, turn the
head unit’s volume control to the 3/4 position.
C Turn Input Level control clockwise until the
bass output is proportionate to the output of
the high-frequency speakers, according to
your preference.
D Input level is now adjusted correctly.
C
Setting the Crossover
A Crossover setting for subwoofers.
Note: Acceptable frequency ranges are indicated
in gray.
D
Remote Level Control (optional)
The Remote Level Control, if installed, will allow
you to adjust the level of bass while seated in the
listening position.
GTO24001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER’S MANUAL
Factory Bolt Ring Connector
Ground Wire
Note: Remove any paint
below ring connector.
Star Washer
This product is designed for mobile applications and is not
intended for connection to the mains.
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change
without notice.
Fuse Holder
150A
4-Gauge
(4 AWG,
22mm
2
)
Inside Engine Compartment
Battery
0-Gauge
(0 AWG,
53.5mm
2
)
Fuse Holder
300A
4-Gauge
(4 AWG,
22mm
2
)
0-Gauge
(0 AWG,
53.5mm
2
)
Distribution Block
Battery
Inside Engine Compartment
0-Gauge
(0 AWG,
53.5mm
2
)
ENGLISH
0158CSK - JBL GTO24001 OM.qxp:Layout 1 13/08/09 15:47 Side 5