Programming Times, Power Levels and
Two-Stage Heating
Any button may be programmed for:
• Heating time from 1 second to 39 minutes and 59
seconds (:01 to 39:59).
• Any of the five power levels: 100%, 80%, 50%, 30%
or Defrost II.
• "Two-Stage" cooking: Defrost II (up to 39:59) plus
any of the other four power levels (100%, 80%, 50%
or 30%; up to 39:59) combined into a single button.
This allows you to defrost and reheat food to serving
temperature with a single button push.
To reprogram the times you want:
1. Open the oven door, leave open.
2. Enter the "Manager's Mode" (programming) code
"614", push buttons 6, 1 and 4.
3. Close the oven door, note "PROG" or flashing
colons on early models in display indicating the
timer is in the "MANAGER'S MODE".
NOTE: Early production ovens (Rev. 000, .A) show
flashing colons, all other revisions (.B and
later) will show "PROG" in the display.
If you make an error while programming, push the
"Change Time" button once to clear the error. Go back
to the programming step you were on.
If one minute elapses before you push a button the
oven will shut down. To continue programming, re-
enter the "Manager's Mode" and begin with the last
button you were reprogramming.
For each button to be programmed:
4. a. Push the button to be reprogrammed. Note
that the button number and the programmed
time appear in the display.
b. Push the "Defrost II" button. The "Defrost II"
time previously programmed will appear in the
display (0 to 39:59; blank = 0).
To change the
time, go to the Time Change Procedure on
page **.
c. Push button 5 to move to the next step.
d. Push the same button number you were pro-
gramming. The time previously programmed
at 100%, 80%, 50% or 30% will appear in the
display. (0 to 39:50; blank =0).
To change to
time, refer to the Time Change Procedure.
e. To change to a different power level, push the
desired button: 100%, 80%, 50% or 30%.
f. Push button 5.
NOTE: If you programmed a "Defrost II" time plus
another time at 100%, 80%, 50% or 30%
power on the same button, that button will
provide "two-stage" cooking.
Example: If you select 2:00 of "Defrost II" plus 1:00 of
80% power on a button, the total cycle time will equal 3:00
for that button. The oven will defrost for two minutes and
heat for one minute to heat the food from frozen to ready,
per your instructions.
5. Go back to step 4a for the next button to be
programmed.
6. When you have completed programming the buttons
you wish to change, open and close the oven door to
exit the "Manager's Mode" and go back to normal
operation, or let the oven shut itself down (in 60
seconds).
7. Time change procedures for steps 4b and 4d:
Push and hold in button 1
to change seconds "00:01"
Push and hold in button 2
to change tens of seconds "00:10"
Push and hold in button 3
to change minutes "01:00"
Push and hold in button 4
to change tens of minutes "10:00"
NOTE:
If you miss the number you want, continue to
hold. Momentary pushes will advance the count
one number at a time.
When you have entered the time you want, go to step 4c
or 4e.
Deactivation and Reactivation of "Change
Time" Button
1. Open the oven door, leave open.
2. Enter the "Manager's Mode" (programming) code
"614" by pushing buttons 6, 1 and 4.
If you make an error, close the oven door and go back
to step 1.
3. Close oven door.
Note: "PROG" or flashing colons on early models in
display indicating the timer is in the
"MANAGER'S MODE". If not, repeat from step 1.
NOTE: Early production ovens (Rev. 000, .A) show
flashing colons, all other revisions (.B and later)
will show "PROG" in the display.
4. Push the "Change Time" button.
5. To deactivate the "Change Time" feature, push button
9.
To reactivate the "Change Time" feature, push button
8.
6. Open and close the oven door to exit the "Manager's
Mode" and go back to normal operation, or let the
oven shut itself down (in 60 seconds).
