Aquavision AVF 104-4 Installation Manual

Download Installation manual of Aquavision AVF-10.4-4 LCD TV, Smart TV for Free or View it Online on All-Guides.com. This version of Aquavision AVF-10.4-4 Manual compatible with such list of devices, as: AVF-10.4-4, AVF-19-4, AVF-20-4, AVF 104-4B, AVF 17W-4

Aquavision AVF-10.4-4 Installation manual - Page 1
1
Aquavision AVF-10.4-4 Installation manual - Page 2
2
WWW.AQUAVISION.CO.UK
Tel +44 (0)1992 708333
Bezel Installation Guide
Bezel Installation GuideBezel Installation Guide
Bezel Installation Guide
Thank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISIONThank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISION
®
®®
®
Television.
Television.Television.
Television.
Safety
SafetySafety
Safety
AQUAVISION
®
recommends installation to be carried out by a qualified installer. Please ensure that the latest wiring and
safety regulations are adhered. If your AQUAVISION
®
is powered by a low voltage (12/24v DC) power supply unit, this
should be positioned away from any water source. Please observe the safety zones in bathrooms and other wet areas. IF
IF IF
IF
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST B
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST BIN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST B
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST BE EARTHED
E EARTHEDE EARTHED
E EARTHED
Positioning
PositioningPositioning
Positioning
Each AQUAVISION
®
model has specific viewing angles. Position the front bezel in order to view the picture clearly from
all intended areas. Should there be any doubt, make the area safe and power up the LCD, positioning the screen until
satisfied that the picture does not darken or disappear from view.
Wall
Wall Wall
Wall M
MM
Mounting and
ounting and ounting and
ounting and C
CC
Cable
able able
able F
FF
Feed
eedeed
eed
When the position has been defined, cut a hole in the wall to the cut-out dimensions specified for your AQUAVISION
®
model (Fig. 2).
Next, fit the two side mounting brackets into the sides of the hole following the guidance offered in either Fig. 3 or 4
depending on the wall structure.
Fig. 3 uses the brackets as a clamp between the front and back of a partition (stud) wall or in Fig. 4 the bezel brackets
must be fixed to a solid wall using six screws (not provided).
Do not over tighten the screws holding the front bezel onto the brackets as this can distort the frame and may hinder
installation of the glass on the final fix. When fitted, the unit should be able to withstand a potential pull force of 100Kg.
Run the cables to their positions as shown in Fig. 1, ensuring that there is enough cable slack to connect to the rear of the
AQUAVISION® unit. Ensure that the cables are easily available and cannot fall back into the cavity, etc.
Final
Final Final
Final Fix
FixFix
Fix
The wall can now be tiled. You must take care not to bend or damage the inner flange of the bezel as this could
potentially hinder any water-proofing qualities and thus void any guarantee. Note it is not advisable to use raised border
tiles under the edge of the bezel frame. Once all tiles or similar have been fitted and the wall is in a finished state, loosen
the bezel screws and apply a bead of silicon all around the rear of the flange (See Fig. 3 or 4). This prevents moisture
from accessing the sides of the front bezel. Tighten the front panel ensuring the silicone fills any areas that could allow
ingress of water. The bezel is now in position to accommodate the LCD unit and finally the glass panel. Instructions on
fitting these components are supplied separately.
CABLING SCHEMATIC
CABLING SCHEMATICCABLING SCHEMATIC
CABLING SCHEMATIC
Fig 1
Fig 1Fig 1
Fig 1