NEC HT1000 Installation Manual

Download Installation manual of NEC HT1000 - Showcase Series XGA DLP Projector Projector, Projector Accessories for Free or View it Online on All-Guides.com.

NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 1
1
NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 2
2
NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 3
3
NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 4
4
NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 5
5
NEC HT1000 - Showcase Series XGA DLP Projector Installation manual - Page 6
6
NEC Solutions (America), Inc.
Visual Systems
HT1000/1100 Installation Guide
Used with optional NEC Anamorphic Lens (HT169-Lens) v1.0
Contents
www.necvisualsystems.com HT1000/1100 + Anamorphic Lens Page 1 of 6
Product Description, Lens Specs, Screen/Aspect Ratio,
Notes and Formulas
Pg 1
Diagrams & Distance Charts
Pg 2
Cabinet Dimensions; Top, Front and Right
Pg 3
Bottom, Back and Left
Pg 4
Ceiling Mount Dimensions
Pg 5
Input Panel and Control Codes
Pg 6
Product Description
Type: 1 chip DMD
TM
projector Color Wheel: 6 Segments (improved in HT1100)
Resolution: 1024 x 768 (Anamorphic mode) Dimensions: 10.24”(W) x 4.74”(H) x 12.56”(D)
Aspect Ratio: 16:9 Weight: 7.1 lbs
Contrast Ratio: HT1000: 3000:1 (2000:1 Iris open) Brightness: HT1000: 1000 ANSI Lumens
HT1100: 3500:1 (2000:1 Iris open) HT1100: 1100 ANSI Lumens
Std Lens Specifications
Throw Ratio: 1.5-1.9:1 (for 100” diagonal) Manual Focus/Manual Zoom/Manual Iris
Offset Angle: 15.8
°
-18.8
°
(for 100” diagonal) Focal Length: 22.4mm 27.0mm
Screen Sizes: 40”-200” diagonal (16:9) F/#: HT1000: 2.5 3.7
30”-200” diagonal (4:3) HT1100: 2.5 4.5 (due to new Iris)
NEC Anamorphic Lens (HT169-Lens)
The optional NEC Anamorphic Lens attaches to the existing standard lens without changing throw distance or image size. The lens
performs a vertical squeeze allowing the full 4:3 panel resolution (1024x768) to be used and have the image fit a 16:9 screen
appropriately. The lens causes a minor shift vertically to the image position, the values in the formulas below takes this into account.
Screen/Aspect Ratio
A 16:9 screen is recommended for best use of the anamorophic lens and the projectors aspect ratio contols.
The “Anamorphic” setting should be selected in the “Setup/Screen” menu when the projector is used with the optional NEC
Anamorphic Lens. This setting configures the aspect ratio controls so they work appropriately when an anamorphic lens is
used. Aspect ratio control is available for both 16:9 and 4:3 sources using NEC developed scaling technology.
*Firmware is available for the HT1000 allowing ‘Anamorphic’ mode to be selected in the ‘Screen’ menu.
Notes
For screen sizes not indicated in the projection charts, use the formulas below.
The ceiling must be strong enough to support the projector and the installation must be in accordance with any local
building codes.
Distances are in inches, for millimeters multiply by 25.4.
Distances may vary ±5%.
Formulas
The Projection Formulas use the image width for calculation. Image width is the same for all aspect ratios, only vertical image size
varies. For proper projector placement, determine the image width for a desired screen size. Use the Screen Formulas below to
calculate all screen dimensions. Plug in the image width for “W” in the Projection Formulas.
Refer to the diagrams and charts for popular screen sizes on page 2.
Note: Distances are measured at the standard lens. The Anamorphic lens is attached after installation.
Projection Formulas: (using a 16:9 screen) Definitions:
B = 0.54405W 0.021 W = Image Width
C(wide) = 1.5607W 1.751 H = Image Height (Size)
C(tele) = 1.8789W 1.694 B = Vertical distance between lens center and screen center
D = 0.2628W 0.021 C = Throw distance
α(wide) = tan
-1
(B/C(wide)) D = Vertical distance between lens center and screen bottom
α(tele) = tan
-1
(B/C(tele)) (screen top for ceiling mounted application)
16:9 Screen Formulas:
W = H x 16/9
Note: Vertical Position is not available in Anamorphic mode. H = W x 9/16
Screen Diagonal = W x 18.358/16